Don't work after upgrade

[usuarioforum]

After upgrade to last version (XS2.ar2316.v3.3.2.4257.090214.1451), when I connect to Picostation (ap configuration) wiht a pda or computer, pico lost connection (I can't ping over ethernet). Then can ping, but when I want to connect again via wifi, the same...

There is a problem with new firmware?

Config:

aaa.1.status=disabled
aaa.status=disabled
bridge.1.devname=br0
bridge.1.fd=1
bridge.1.port.1.devname=eth0
bridge.1.port.1.status=enabled
bridge.1.port.2.devname=ath0
bridge.1.port.2.status=enabled
bridge.1.stp.status=disabled
bridge.status=enabled
dhcpc.1.devname=br0
dhcpc.1.status=disabled
dhcpc.status=disabled
dhcpd.1.status=disabled
dhcpd.status=disabled
dnsmasq.1.devname=eth0
dnsmasq.1.status=enabled
dnsmasq.status=disabled
ebtables.1.cmd=-t nat -A PREROUTING --in-interface ath0 -j arpnat --arpnat-target ACCEPT
ebtables.1.status=disabled
ebtables.2.cmd=-t nat -A POSTROUTING --out-interface ath0 -j arpnat

--arpnat-target ACCEPT
ebtables.2.status=disabled
ebtables.3.cmd=-t broute -A BROUTING --protocol

0x888e --in-interface ath0 -j DROP
ebtables.3.status=disabled
ebtables.50.status=disabled
ebtables.51.status=disabled
ebtables.52.status=disabled
ebtables.status=enabled
httpd.port=80
httpd.status=enabled
igmpproxy.status=disabled
iptables.3.status=disabled
iptables.status=disabled
netconf.1.alias.1.status=disabled
netconf.1.alias.2.status=disabled
netconf.1.alias.3.status=disabled
netconf.1.alias.4.status=disabled
netconf.1.alias.5.status=disabled
netconf.1.alias.6.status=disabled
netconf.1.alias.7.status=disabled
netconf.1.alias.8.status=disabled
netconf.1.devname=eth0
netconf.1.ip=0.0.0.0
netconf.1.netmask=255.255.255.0
netconf.1.promisc=enabled
netconf.1.status=enabled
netconf.1.up=enabled
netconf.2.alias.1.status=disabled
netconf.2.alias.2.status=disabled
netconf.2.alias.3.status=disabled
netconf.2.alias.4.status=disabled
netconf.2.alias.5.status=disabled
netconf.2.alias.6.status=disabled
netconf.2.alias.7.status=disabled
netconf.2.alias.8.status=disabled
netconf.2.allmulti=disabled
netconf.2.devname=ath0
netconf.2.ip=0.0.0.0
netconf.2.netmask=255.255.255.0
netconf.2.status=enabled
netconf.2.up=enabled
netconf.3.autoip.status=enabled
netconf.3.devname=br0
netconf.3.ip=192.168.101.5
netconf.3.netmask=255.255.255.0
netconf.3.status=enabled
netconf.3.up=enabled
netconf.status=enabled
netmode=bridge
ppp.1.password=
ppp.1.status=disabled
ppp.status=disabled
radio.1.ack.auto=enabled
radio.1.ackdistance=4050
radio.1.acktimeout=48
radio.1.ani.status=disabled
radio.1.channel=1
radio.1.chanshift=0
radio.1.clksel=0
radio.1.countrycode=724
radio.1.devname=ath0
radio.1.dfs.status=
radio.1.frag=off
radio.1.ieee_mode=g
radio.1.mcastrate=1M
radio.1.mode=master
radio.1.rate.auto=enabled
radio.1.rate.max=54M
radio.1.rts=off
radio.1.rx_antenna=1
radio.1.rx_antenna_diversity=disabled
radio.1.status=enabled
radio.1.thresh62a=28
radio.1.thresh62b=28
radio.1.thresh62g=28
radio.1.tx_antenna=1
radio.1.tx_antenna_diversity=disabled
radio.1.txpower=16
radio.countrycode=724
radio.ratemodule=ath_rate_sample
radio.status=enabled
resolv.nameserver.1.ip=0.0.0.0
resolv.nameserver.1.status=enabled
resolv.nameserver.2.status=disabled
resolv.status=enabled
route.1.devname=br0
route.1.gateway=192.168.101.1
route.1.ip=0.0.0.0
route.1.netmask=0
route.1.status=enabled
route.status=enabled
tshaper.status=disabled
users.1.name=ubnt
users.1.password=VvpvCwhccFv6Q
users.1.status=enabled
users.status=enabled
wireless.1.addmtikie=enabled
wireless.1.ap=
wireless.1.authmode=1
wireless.1.compression=0
wireless.1.devname=ath0
wireless.1.fastframes=0
wireless.1.frameburst=0
wireless.1.hide_ssid=disabled
wireless.1.l2_isolation=disabled
wireless.1.mac_acl.1.mac=
wireless.1.mac_acl.1.status=disabled
wireless.1.mac_acl.10.mac=
wireless.1.mac_acl.10.status=disabled
wireless.1.mac_acl.11.mac=
wireless.1.mac_acl.11.status=disabled
wireless.1.mac_acl.12.mac=
wireless.1.mac_acl.12.status=disabled
wireless.1.mac_acl.13.mac=
wireless.1.mac_acl.13.status=disabled
wireless.1.mac_acl.14.mac=
wireless.1.mac_acl.14.status=disabled
wireless.1.mac_acl.15.mac=
wireless.1.mac_acl.15.status=disabled
wireless.1.mac_acl.16.mac=
wireless.1.mac_acl.16.status=disabled
wireless.1.mac_acl.2.mac=
wireless.1.mac_acl.2.status=disabled
wireless.1.mac_acl.3.mac=
wireless.1.mac_acl.3.status=disabled
wireless.1.mac_acl.4.mac=
wireless.1.mac_acl.4.status=disabled
wireless.1.mac_acl.5.mac=
wireless.1.mac_acl.5.status=disabled
wireless.1.mac_acl.6.mac=
wireless.1.mac_acl.6.status=disabled
wireless.1.mac_acl.7.mac=
wireless.1.mac_acl.7.status=disabled
wireless.1.mac_acl.8.mac=
wireless.1.mac_acl.8.status=disabled
wireless.1.mac_acl.9.mac=
wireless.1.mac_acl.9.status=disabled
wireless.1.mac_acl.policy=allow
wireless.1.mac_acl.status=disabled
wireless.1.macclone=disabled
wireless.1.security=none
wireless.1.signal_led1=94
wireless.1.signal_led2=80
wireless.1.signal_led3=73
wireless.1.signal_led4=65
wireless.1.sper=disabled
wireless.1.ssid=UBNT
wireless.1.status=enabled
wireless.1.wds=disabled
wireless.1.wmm=disabled
wireless.1.wmmlevel=-1
wireless.status=enabled
wpasupplicant.device.1.status=disabled
wpasupplicant.status=disabled

[UBNT-Mike.Ford]

Hello,

Please email me at mike@ubnt.com

Thanks,

Mike

[usuarioforum]

Mike:

I sent an email to you. Do you have it?

Cheers

[usuarioforum]

No answer?????

[skyhook]

Have you tried to hold reset for about 30 sec?
Have you tried the AirOS Factory Firmware Recovery Procedure?
http://www.ubnt.com/downloads/LS-Recovery.txt

[usuarioforum]

I send the email sended to Mike:

I have bought 10 pico station and I go testing. With release 3.2.3 I can connect my pda (htc touch) to ubnt and I have ip (provided by the router, no by the ubnt. Ubnt is in switch mde), but pda can't connect to the lan. Can't ping from any computer to pda.

With release 3.3.2 pda can't connect to ubnt. Now ubnt don't loose conectivity by lan, don't restart, but can't connect with my pda. "I tested again yesterday and lose connectivity again". I think the ap reboot.

Is very important to work with pda because this ap's are for a test with the police in my city. Now we will test with 10 ap's but if the test is good we must to by more than 50 ap's this year.

You now some firmware release that work good with pda?

Thanks.

[usuarioforum]

??

No solution?

Not very good support.

[skyhook]

??

No solution?

Not very good support.

Try to disable "Enable Extra Reporting:" in ADVANCED TAB.