WISPSTATION Signal Strenght problem

[mackosy]

Hi!
I have a wispstation 5 and a TP-Link TL-WN653AG PCI in a PC with Mikrotik routeros.
With PC i have -56dBm signal strenght, but if i change to Wispstation the signal strenght is only -80,-81.
Antenna position and cable is the same in both.
What is the problem?
I already tried openwrt,ddwrt, lot of settings but the effect was always the same.
Somebody van help me?
Regards

[UBNT-Mike.Ford]

Hello,

Please post your firmware version number and the configuraion file for the WS5.

Thanks,

Mike

[mackosy]

Here s my config:
aaa.1.status=disabled
aaa.status=disabled
bridge.1.devname=br0
bridge.1.fd=1
bridge.1.port.1.devname=eth0
bridge.1.port.1.status=enabled
bridge.1.port.2.devname=ath0
bridge.1.port.2.status=enabled
bridge.1.stp.status=disabled
bridge.status=enabled
dhcpc.1.devname=br0
dhcpc.1.status=disabled
dhcpc.status=disabled
dhcpd.1.status=disabled
dhcpd.status=disabled
dnsmasq.1.devname=eth0
dnsmasq.1.status=enabled
dnsmasq.status=disabled
ebtables.1.cmd=-t nat -A PREROUTING --in-interface ath0 -j arpnat --arpnat-target ACCEPT
ebtables.1.status=disabled
ebtables.2.cmd=-t nat -A POSTROUTING --out-interface ath0 -j arpnat --arpnat-target ACCEPT
ebtables.2.status=disabled
ebtables.3.cmd=-t broute -A BROUTING --protocol 0x888e --in-interface ath0 -j DROP
ebtables.3.status=disabled
ebtables.50.status=disabled
ebtables.51.status=disabled
ebtables.52.status=disabled
ebtables.status=enabled
httpd.port=80
httpd.status=enabled
igmpproxy.status=disabled
iptables.3.status=disabled
iptables.status=disabled
netconf.1.alias.1.status=disabled
netconf.1.alias.2.status=disabled
netconf.1.alias.3.status=disabled
netconf.1.alias.4.status=disabled
netconf.1.alias.5.status=disabled
netconf.1.alias.6.status=disabled
netconf.1.alias.7.status=disabled
netconf.1.alias.8.status=disabled
netconf.1.devname=eth0
netconf.1.ip=0.0.0.0
netconf.1.netmask=255.255.255.0
netconf.1.promisc=enabled
netconf.1.status=enabled
netconf.1.up=enabled
netconf.2.alias.1.status=disabled
netconf.2.alias.2.status=disabled
netconf.2.alias.3.status=disabled
netconf.2.alias.4.status=disabled
netconf.2.alias.5.status=disabled
netconf.2.alias.6.status=disabled
netconf.2.alias.7.status=disabled
netconf.2.alias.8.status=disabled
netconf.2.devname=ath0
netconf.2.ip=0.0.0.0
netconf.2.netmask=255.255.255.0
netconf.2.status=enabled
netconf.2.up=enabled
netconf.3.autoip.status=enabled
netconf.3.devname=br0
netconf.3.ip=172.16.16.65
netconf.3.netmask=255.255.255.0
netconf.3.status=enabled
netconf.3.up=enabled
netconf.status=enabled
netmode=bridge
ppp.1.password=
ppp.1.status=disabled
ppp.status=disabled
radio.1.ack.auto=enabled
radio.1.acktimeout=25
radio.1.chanshift=0
radio.1.clksel=0
radio.1.countrycode=840
radio.1.devname=ath0
radio.1.ieee_mode=ast
radio.1.mcastrate=6M
radio.1.mode=managed
radio.1.rate.auto=enabled
radio.1.rate.max=54M
radio.1.rx_antenna=1
radio.1.rx_antenna_diversity=disabled
radio.1.status=enabled
radio.1.tx_antenna=1
radio.1.tx_antenna_diversity=disabled
radio.1.txpower=19
radio.countrycode=840
radio.ratemodule=ath_rate_minstrel
radio.status=enabled
resolv.nameserver.1.ip=0.0.0.0
resolv.nameserver.1.status=enabled
resolv.nameserver.2.status=disabled
resolv.status=enabled
route.1.devname=br0
route.1.gateway=172.16.16.254
route.1.ip=0.0.0.0
route.1.netmask=0
route.1.status=enabled
route.status=enabled
users.1.name=ubnt
users.1.password=VvpvCwhccFv6Q
users.1.status=enabled
users.status=enabled
wireless.1.ap=
wireless.1.authmode=1
wireless.1.devname=ath0
wireless.1.hide_ssid=disabled
wireless.1.macclone=disabled
wireless.1.scan_list.status=disabled
wireless.1.security=none
wireless.1.ssid=TYUXAR120
wireless.1.status=enabled
wireless.1.wds=enabled
wireless.status=enabled
wpasupplicant.device.1.status=disabled
wpasupplicant.status=disabled
The firmware : MS5.ar2313.v3.2.3-rc.4063.081124.1740.bin
Thank You.
Hello,

Please post your firmware version number and the configuraion file for the WS5.

Thanks,

Mike

[UBNT-Mike.Ford]

Hello,

Can you try either A) a different WISPsation or B) a different U.FL pigtail?

Thanks,

MIke

[mackosy]

Hi!
Not yet.I bought one piece for try out.
I will try it with another pigtail tonight.
Thanks
quote="UBNT-Mike.Ford"]Hello,

Can you try either A) a different WISPsation or B) a different U.FL pigtail?

Thanks,

MIke[/quote]

[upowaushyi]

Hi!
Not yet.I bought one piece for try out.
I will try it with another pigtail tonight.
Thanks
quote="UBNT-Mike.Ford"]Hello,

Can you try either A) a different WISPsation or B) a different U.FL pigtail?

Thanks,

MIke[/quote]
Yes! i have the same problem(

[UBNT-Mike.Ford]

Hello,

Any update?

Thanks,

Mike

[mackosy]

Hi!
Sorry for my late answer, i was busy...
I was try it another pigtail, and another antenna too, but the effect was the same.
I think wispstation wont be my friend....
Regards
Hello,

Any update?

Thanks,

Mike

[UBNT-Mike.Ford]

Hello Mackosy,

Shoot me an email to mike@ubnt.com and ill replace it so that I can test that one here.

Thanks,

Mike

[zoki]

Hello
I have the same problem.
I bought 15 pieces wisp5 devices and all have a problem with a small output through 5280 MHz.
Excellent work only on the lower frequencies (5180,5200,5220,5240,5260 and 5280)
All are made 03/12/2009.
I will definitely return to vendor.

Regards