Mtneer
01-04-2009, 10:45 PM
I'm configuring a new PS2. I am 35 feet from the AP antenna (and yes, I tried lowering the output power all the way down, and it made no difference). I have 20 CPEs (different brands) located up to a quarter mile away and they all work great off of this same AP. On this PS2, I have 1.0 Mbps TX Rate and 1.0 Mbps RX Rate, and the Transmit CCQ is anywhere between 8% and 1% and throughput is horrible. Any ideas on remedying this? It drops down to these settings almost immediately after any configuration changes to the PS2.
Firmware version: XS2.ar2316.v3.1.1.3498.080725.1324
Here is my config:
users.status=enabled bridge.1.stp.status=disabled igmpproxy.status=disabled ebtables.51.status=disabled ebtables.50.status=disabled iptables.3.status=disabled wireless.1.scan_list.status=disabled radio.1.chanshift=0 radio.1.dfs.status= wireless.1.addmtikie=enabled wireless.1.sper=disabled wireless.1.signal_led4=65 wireless.1.signal_led3=73 wireless.1.signal_led2=80 wireless.1.signal_led1=94 iptables.2.status=disabled iptables.1.status=enabled iptables.1.cmd=-t nat -I POSTROUTING -o ath0 -j MASQUERADE dhcpd.1.lease_time=3600 dhcpd.1.netmask= dhcpd.1.end=172.17.2.200 dhcpd.1.start=172.17.2.100 dhcpd.1.devname=eth0 resolv.host.1.name=NVS resolv.host.1.status=enabled wpasupplicant.device.1.status=disabled wpasupplicant.status=disabled aaa.1.status=disabled aaa.status=disabled wireless.1.ap= wireless.1.authmode=1 radio.1.clksel=0 radio.1.countrycode=840 wireless.1.macclone=disabled wireless.1.wds=disabled ebtables.3.cmd=-t broute -A BROUTING --protocol 0x888e --in-interface ath0 -j DROP ebtables.3.status=disabled ebtables.2.cmd=-t nat -A POSTROUTING --out-interface ath0 -j arpnat --arpnat-target ACCEPT ebtables.2.status=enabled ebtables.1.cmd=-t nat -A PREROUTING --in-interface ath0 -j arpnat --arpnat-target ACCEPT ebtables.1.status=enabled ebtables.status=enabled route.1.netmask=0 route.1.ip=0.0.0.0 route.1.gateway=10.61.32.1 route.1.devname=br0 route.1.status=enabled route.status=enabled dhcpc.1.devname=br0 dhcpc.1.status=disabled dhcpc.status=disabled dhcpd.1.status=disabled dhcpd.status=disabled netconf.3.up=enabled netconf.3.netmask=255.255.240.0 netconf.3.ip=10.61.44.27 netconf.3.devname=br0 netconf.3.status=enabled netconf.2.up=enabled netconf.2.netmask=255.255.255.0 netconf.2.ip=0.0.0.0 netconf.2.devname=ath0 netconf.2.status=enabled netconf.1.promisc=enabled netconf.1.up=enabled netconf.1.netmask=255.255.255.0 netconf.1.ip=0.0.0.0 netconf.1.devname=eth0 netconf.1.status=enabled netconf.status=enabled bridge.1.port.2.devname=ath0 bridge.1.port.1.devname=eth0 bridge.1.fd=1 bridge.1.devname=br0 bridge.status=enabled wireless.1.rssi_led4=30 wireless.1.rssi_led3=22 wireless.1.rssi_led2=15 wireless.1.rssi_led1=1 wireless.1.hide_ssid=disabled wireless.1.ssid=Metro5573-AP wireless.1.security=none wireless.1.devname=ath0 wireless.1.status=enabled wireless.status=enabled radio.1.tx_antenna=1 radio.1.rx_antenna=1 radio.1.tx_antenna_diversity=disabled radio.1.rx_antenna_diversity=disabled radio.1.acktimeout=61 radio.1.txpower=1 radio.1.ieee_mode=b radio.1.rate.auto=enabled radio.1.rate.max=11M radio.1.mode=managed radio.1.devname=ath0 radio.1.status=enabled radio.ratemodule=ath_rate_onoe radio.countrycode=840 radio.status=enabled httpd.port.http=80 httpd.status=enabled users.1.password=xxxxxxx users.1.name=xxxxxxxxx users.1.status=enabled ppp.1.password= ppp.status=disabled ppp.1.status=disabled iptables.status=disabled resolv.nameserver.1.status=disabled resolv.nameserver.1.ip= resolv.nameserver.2.status=disabled resolv.nameserver.2.ip= resolv.status=enabled netmode=bridge wireless.1.wmm=disabled wireless.1.wmmlevel=-1 radio.1.rts=off radio.1.frag=off radio.1.ack.auto=disabled wireless.1.fastframes=disabled wireless.1.frameburst=disabled wireless.1.compression=disabled radio.1.ext_antenna=disabled tshaper.status=disabled netconf.2.allmulti=disabled radio.1.mcastrate=1M wireless.1.l2_isolation=enabled radio.1.thresh62a=28 radio.1.thresh62b=28 radio.1.thresh62g=28
Firmware version: XS2.ar2316.v3.1.1.3498.080725.1324
Here is my config:
users.status=enabled bridge.1.stp.status=disabled igmpproxy.status=disabled ebtables.51.status=disabled ebtables.50.status=disabled iptables.3.status=disabled wireless.1.scan_list.status=disabled radio.1.chanshift=0 radio.1.dfs.status= wireless.1.addmtikie=enabled wireless.1.sper=disabled wireless.1.signal_led4=65 wireless.1.signal_led3=73 wireless.1.signal_led2=80 wireless.1.signal_led1=94 iptables.2.status=disabled iptables.1.status=enabled iptables.1.cmd=-t nat -I POSTROUTING -o ath0 -j MASQUERADE dhcpd.1.lease_time=3600 dhcpd.1.netmask= dhcpd.1.end=172.17.2.200 dhcpd.1.start=172.17.2.100 dhcpd.1.devname=eth0 resolv.host.1.name=NVS resolv.host.1.status=enabled wpasupplicant.device.1.status=disabled wpasupplicant.status=disabled aaa.1.status=disabled aaa.status=disabled wireless.1.ap= wireless.1.authmode=1 radio.1.clksel=0 radio.1.countrycode=840 wireless.1.macclone=disabled wireless.1.wds=disabled ebtables.3.cmd=-t broute -A BROUTING --protocol 0x888e --in-interface ath0 -j DROP ebtables.3.status=disabled ebtables.2.cmd=-t nat -A POSTROUTING --out-interface ath0 -j arpnat --arpnat-target ACCEPT ebtables.2.status=enabled ebtables.1.cmd=-t nat -A PREROUTING --in-interface ath0 -j arpnat --arpnat-target ACCEPT ebtables.1.status=enabled ebtables.status=enabled route.1.netmask=0 route.1.ip=0.0.0.0 route.1.gateway=10.61.32.1 route.1.devname=br0 route.1.status=enabled route.status=enabled dhcpc.1.devname=br0 dhcpc.1.status=disabled dhcpc.status=disabled dhcpd.1.status=disabled dhcpd.status=disabled netconf.3.up=enabled netconf.3.netmask=255.255.240.0 netconf.3.ip=10.61.44.27 netconf.3.devname=br0 netconf.3.status=enabled netconf.2.up=enabled netconf.2.netmask=255.255.255.0 netconf.2.ip=0.0.0.0 netconf.2.devname=ath0 netconf.2.status=enabled netconf.1.promisc=enabled netconf.1.up=enabled netconf.1.netmask=255.255.255.0 netconf.1.ip=0.0.0.0 netconf.1.devname=eth0 netconf.1.status=enabled netconf.status=enabled bridge.1.port.2.devname=ath0 bridge.1.port.1.devname=eth0 bridge.1.fd=1 bridge.1.devname=br0 bridge.status=enabled wireless.1.rssi_led4=30 wireless.1.rssi_led3=22 wireless.1.rssi_led2=15 wireless.1.rssi_led1=1 wireless.1.hide_ssid=disabled wireless.1.ssid=Metro5573-AP wireless.1.security=none wireless.1.devname=ath0 wireless.1.status=enabled wireless.status=enabled radio.1.tx_antenna=1 radio.1.rx_antenna=1 radio.1.tx_antenna_diversity=disabled radio.1.rx_antenna_diversity=disabled radio.1.acktimeout=61 radio.1.txpower=1 radio.1.ieee_mode=b radio.1.rate.auto=enabled radio.1.rate.max=11M radio.1.mode=managed radio.1.devname=ath0 radio.1.status=enabled radio.ratemodule=ath_rate_onoe radio.countrycode=840 radio.status=enabled httpd.port.http=80 httpd.status=enabled users.1.password=xxxxxxx users.1.name=xxxxxxxxx users.1.status=enabled ppp.1.password= ppp.status=disabled ppp.1.status=disabled iptables.status=disabled resolv.nameserver.1.status=disabled resolv.nameserver.1.ip= resolv.nameserver.2.status=disabled resolv.nameserver.2.ip= resolv.status=enabled netmode=bridge wireless.1.wmm=disabled wireless.1.wmmlevel=-1 radio.1.rts=off radio.1.frag=off radio.1.ack.auto=disabled wireless.1.fastframes=disabled wireless.1.frameburst=disabled wireless.1.compression=disabled radio.1.ext_antenna=disabled tshaper.status=disabled netconf.2.allmulti=disabled radio.1.mcastrate=1M wireless.1.l2_isolation=enabled radio.1.thresh62a=28 radio.1.thresh62b=28 radio.1.thresh62g=28
