View Full Version : NS5 station can't loggin into remotely
Gooszer
11-29-2008, 03:17 PM
HI again,
Seems I can't troubleshoot a problem here. I have 2 NS5's one is setup as AP WDS the other as station WDS. From the AP side and i can login into the AP, I can see the bridged connection to the Station. From the remote side i can log into the station and log into the AP. Any thoughts? I still have internet on the remote end...
Gooszer
11-29-2008, 03:27 PM
I power cycled my ap and everthing seems to be online and working..
Gooszer
11-29-2008, 03:37 PM
Alright i'm leaving this until i get a reply...
So i power cycled the AP and as soon as it came back up within a few seconds i logged into the Station WDS. Left it for a few minutes and went back to try logging into the Station... IE cannott display page...
I can ping it, i can see it, but i can't log into it. This isnt because of WDS mode right?
If you can ping it, yer connected o tit. Hit the F5 key on yer keyboard while in IE. See if that fixes it.
Do you have "Enable Client Isolation:" checked ?
IF so, ... try with "Enable Client Isolation:" un-checked.
omarvis
11-29-2008, 09:33 PM
what if you use discovery utility?
its appear?
are u using same network block in brdged network to managed radios? if so, must be ip conflict?
Gooszer
11-29-2008, 11:15 PM
Yes the client isolation is unchecked.
No I can't see it in discovery tool.
I don't understand
"are u using same network block in brdged network to managed radios? if so, must be ip conflict?"
I have no ip conflicts.
Setup as
gateway 1.1 > unmanaged switch(only has 1 pc) > AP WPS 1.20 > Station WPS 1.21 > dlink WAN 1.100 > dlink LAN 2.xx with dhcp server on running wireless to laptop.
Have internet. I can log in from the remote side to the AP. But from the AP side i can't see the Station... messed up... going to sleep on it... i went through the GUI again and everything is the same, made a change to security and went with WPA2. I should mention that these two radios are being tested in my work area, and basically sitting 3 feet apart facing each other (can't see that being an issue tho).
guidonet
11-30-2008, 07:12 AM
Uncheck DMZ
Gooszer
11-30-2008, 08:11 AM
DMZ isnt even an option on the AP
Gooszer...
If you can ping it, but not see it with the discovery tool...something isn't right.
Gooszer
11-30-2008, 12:08 PM
being that i only have one link, i'm just going to go back to factory defaults on the station... i'll let you know how it turns out. thanks for the ideas people
guidonet
11-30-2008, 02:11 PM
DMZ still an option... even in AP mode.... just check "Network" tab... if you´re using the router mode DMZ will be there.
Gooszer
11-30-2008, 04:08 PM
ya i'm using bridge mode
Gooszer
11-30-2008, 05:45 PM
k after reset, and set it all back up, everything is running fine. I found i was using the DHCP setting on the wireless router to get internet. changed it to static and seems that everything is working peachy. I am still using the wan port on the router
later
UBNT-Mike.Ford
12-01-2008, 01:04 PM
Thanks for the update.
Mike
Gooszer
12-10-2008, 01:47 PM
so after it got all setup again and it worked for a day it happened again.... i still understand it myself. however I added the station side WLAN MAC in to the APs list of WDS Peers. I also added the DNS to both the station and AP under the networking. as of now 24 hours it's working from both ends.
