2x Nanostation 5, WPA/WPA2 not working.

[BeAuMaN]

Note: Test results and theory beginning on page 2

'lo

I'm hoping that this is either a brainfart or something to do with my inexperience with wireless networks... but my problem seems to be related to WPA/WPA2.

After some more careful reading, fiddling, and what-have-you, I finally got my link setup. Essentially, it's as follows:

Home Network <---> NS5 (Station/Bridge) <~~~> NS5 (AP/Bridge) <---> WISP 802.11a unit <~~~> WISP network

<~~~> = Wireless Link
<---> = Wired Link

It's akin to what I described earlier here (http://forum.ubnt.com/forum/viewtopic.php?t=2991&highlight=).

Got everything setup so that the NS5s were communicating with each other and their corresponding networks. I'm getting great speeds through to WISP.

So, I left the final task to be setting up security, which up until this point I left it open. So I read, and it said to set the access point up first, -then- the station. So I did that. WPA2-AES PSK. First did it to the Access Point remotely... lost connection... then did it to the station by my house, same settings... and as I was expecting them to connect now that they had the same security settings, that was not the case. Tried rebooting the house unit, no connection. Tried rebooting the other unit, no connection. Changed to normal WPA2, same results. WPA, same results.

So, did I do something wrong here? or is it some sort of bug. My connection is back up now that I've changed it back to an open network.

Here's the config:

RadNet1 (Station)

users.status=enabled dhcpc.1.fallback=192.168.1.20 resolv.host.1.name=RadNet1 resolv.host.1.status=enabled bridge.1.stp.status=disabled igmpproxy.status=disabled netmode=bridge ebtables.51.status=disabled ebtables.50.status=disabled resolv.status=enabled resolv.nameserver.2.status=enabled resolv.nameserver.1.status=enabled resolv.nameserver.1.ip=64.192.0.10 iptables.status=disabled ppp.1.status=disabled iptables.3.status=disabled ppp.status=disabled ppp.1.password= wpasupplicant.profile.1.network.1.psk=spiffyjuice wpasupplicant.profile.1.network.1.bssid=00:15:6D:B5:F8:05 wpasupplicant.profile.1.network.1.key_mgmt.1.name=WPA-PSK wpasupplicant.profile.1.name=WPA-PSK wpasupplicant.device.1.profile=WPA-PSK aaa.1.wpa.key.1.mgmt=WPA-PSK aaa.1.wpa.psk=spiffyjuice aaa.1.ssid=RadNet1 aaa.1.br.devname=br0 aaa.1.devname=ath0 aaa.1.driver=madwifi aaa.1.wpa.1.pairwise=CCMP aaa.1.wpa=2 aaa.1.status=disabled aaa.status=disabled wpasupplicant.device.1.status=enabled wpasupplicant.status=enabled wireless.1.mac_acl.16.mac= wireless.1.mac_acl.16.status=disabled wireless.1.mac_acl.15.mac= wireless.1.mac_acl.15.status=disabled wireless.1.mac_acl.14.mac= wireless.1.mac_acl.14.status=disabled wireless.1.mac_acl.13.mac= wireless.1.mac_acl.13.status=disabled wireless.1.mac_acl.12.mac= wireless.1.mac_acl.12.status=disabled wireless.1.mac_acl.11.mac= wireless.1.mac_acl.11.status=disabled wireless.1.mac_acl.10.mac= wireless.1.mac_acl.10.status=disabled wireless.1.mac_acl.9.mac= wireless.1.mac_acl.9.status=disabled wireless.1.mac_acl.8.mac= wireless.1.mac_acl.8.status=disabled wireless.1.mac_acl.7.mac= wireless.1.mac_acl.7.status=disabled wireless.1.mac_acl.6.mac= wireless.1.mac_acl.6.status=disabled wireless.1.mac_acl.5.mac= wireless.1.mac_acl.5.status=disabled wireless.1.mac_acl.4.mac= wireless.1.mac_acl.4.status=disabled wireless.1.mac_acl.3.mac= wireless.1.mac_acl.3.status=disabled wireless.1.mac_acl.2.mac= wireless.1.mac_acl.2.status=disabled wireless.1.mac_acl.1.mac= wireless.1.mac_acl.1.status=disabled wireless.1.mac_acl.policy=allow wireless.1.mac_acl.status=disabled wireless.1.ap=00:15:6D:B5:F8:05 wireless.1.authmode=1 radio.1.chanshift=0 radio.1.clksel=0 radio.1.mcastrate=6M radio.1.countrycode=840 wireless.1.macclone=disabled radio.1.channel=36 wireless.1.wds=disabled users.1.status=enabled users.1.name=ubnt users.1.password=VvpvCwhccFv6Q httpd.status=enabled httpd.port=80 radio.status=enabled radio.countrycode=840 radio.ratemodule=ath_rate_sample radio.1.status=enabled radio.1.devname=ath0 radio.1.mode=managed radio.1.rate.max=54M radio.1.rate.auto=enabled radio.1.ieee_mode=ast radio.1.txpower=19 radio.1.acktimeout=22 radio.1.ack.auto=enabled radio.1.rx_antenna_diversity=disabled radio.1.tx_antenna_diversity=disabled radio.1.rx_antenna=2 radio.1.tx_antenna=2 wireless.status=enabled wireless.1.status=enabled wireless.1.devname=ath0 wireless.1.security=none wireless.1.ssid=RadNet2 wireless.1.hide_ssid=disabled bridge.status=enabled bridge.1.devname=br0 bridge.1.fd=1 bridge.1.port.1.devname=eth0 bridge.1.port.2.devname=ath0 netconf.status=enabled netconf.1.status=enabled netconf.1.devname=eth0 netconf.1.ip=0.0.0.0 netconf.1.netmask=255.255.255.0 netconf.1.up=enabled netconf.1.promisc=enabled netconf.2.status=enabled netconf.2.devname=ath0 netconf.2.ip=0.0.0.0 netconf.2.netmask=255.255.255.0 netconf.2.up=enabled netconf.3.status=enabled netconf.3.devname=br0 netconf.3.ip=64.203.123.38 netconf.3.netmask=255.255.255.240 netconf.3.up=enabled dhcpd.status=disabled dhcpd.1.status=disabled dhcpc.status=disabled dhcpc.1.status=disabled dhcpc.1.devname=br0 route.status=enabled route.1.status=enabled route.1.devname=br0 route.1.gateway=64.203.123.33 route.1.ip=0.0.0.0 route.1.netmask=0 ebtables.status=enabled ebtables.1.status=enabled ebtables.1.cmd=-t nat -A PREROUTING --in-interface ath0 -j arpnat --arpnat-target ACCEPT ebtables.2.status=enabled ebtables.2.cmd=-t nat -A POSTROUTING --out-interface ath0 -j arpnat --arpnat-target ACCEPT ebtables.3.status=enabled ebtables.3.cmd=-t broute -A BROUTING --protocol 0x888e --in-interface ath0 -j DROP wireless.1.wmm=disabled wireless.1.wmmlevel=-1 radio.1.rts=off radio.1.frag=off wireless.1.fastframes=enabled wireless.1.frameburst=enabled wireless.1.compression=enabled radio.1.ext_antenna=disabled wireless.1.signal_led1=94 wireless.1.signal_led2=80 wireless.1.signal_led3=73 wireless.1.signal_led4=65 tshaper.status=disabled wireless.1.sper=disabled wireless.1.addmtikie=enabled radio.1.dfs.status= netconf.2.allmulti=disabled wireless.1.l2_isolation=enabled radio.1.thresh62a=28 radio.1.thresh62b=28 radio.1.thresh62g=28 wireless.1.scan_list.status=disabled resolv.nameserver.2.ip=64.192.0.11 ntpclient.status=enabled ntpclient.1.status=enabled ntpclient.1.server=ntp.ucsd.edu wpasupplicant.device.1.devname=ath0 wpasupplicant.device.1.driver=madwifi wpasupplicant.profile.1.network.1.proto.1.name=WPA wpasupplicant.profile.1.network.1.pairwise.1.name=TKIP CCMP wpasupplicant.profile.1.network.1.ssid=RadNet2


RadNet2 (Access Point)

users.status=enabled radio.1.thresh62g=28 radio.1.thresh62b=28 radio.1.thresh62a=28 wireless.1.l2_isolation=disabled netconf.2.allmulti=disabled radio.1.dfs.status= wireless.1.addmtikie=enabled wireless.1.sper=disabled tshaper.status=disabled wireless.1.signal_led4=65 wireless.1.signal_led3=73 wireless.1.signal_led2=80 wireless.1.signal_led1=94 radio.1.ext_antenna=disabled wireless.1.compression=enabled wireless.1.frameburst=enabled wireless.1.fastframes=enabled radio.1.frag=off radio.1.rts=off wireless.1.wmmlevel=-1 wireless.1.wmm=disabled bridge.1.stp.status=disabled igmpproxy.status=disabled netmode=bridge ebtables.51.status=disabled ebtables.50.status=disabled resolv.status=enabled resolv.nameserver.2.status=enabled resolv.nameserver.1.status=enabled resolv.nameserver.1.ip=64.192.0.10 iptables.status=disabled ppp.1.status=disabled iptables.3.status=disabled ppp.status=disabled ppp.1.password= wpasupplicant.device.1.status=disabled wpasupplicant.status=disabled aaa.1.status=enabled aaa.status=enabled wireless.1.mac_acl.16.mac= wireless.1.mac_acl.16.status=disabled wireless.1.mac_acl.15.mac= wireless.1.mac_acl.15.status=disabled wireless.1.mac_acl.14.mac= wireless.1.mac_acl.14.status=disabled wireless.1.mac_acl.13.mac= wireless.1.mac_acl.13.status=disabled wireless.1.mac_acl.12.mac= wireless.1.mac_acl.12.status=disabled wireless.1.mac_acl.11.mac= wireless.1.mac_acl.11.status=disabled wireless.1.mac_acl.10.mac= wireless.1.mac_acl.10.status=disabled wireless.1.mac_acl.9.mac= wireless.1.mac_acl.9.status=disabled wireless.1.mac_acl.8.mac= wireless.1.mac_acl.8.status=disabled wireless.1.mac_acl.7.mac= wireless.1.mac_acl.7.status=disabled wireless.1.mac_acl.6.mac= wireless.1.mac_acl.6.status=disabled wireless.1.mac_acl.5.mac= wireless.1.mac_acl.5.status=disabled wireless.1.mac_acl.4.mac= wireless.1.mac_acl.4.status=disabled wireless.1.mac_acl.3.mac= wireless.1.mac_acl.3.status=disabled wireless.1.mac_acl.2.mac= wireless.1.mac_acl.2.status=disabled wireless.1.mac_acl.1.mac= wireless.1.mac_acl.1.status=disabled wireless.1.mac_acl.policy=allow wireless.1.mac_acl.status=disabled wireless.1.ap= wireless.1.authmode=1 radio.1.chanshift=0 radio.1.clksel=0 radio.1.mcastrate=6M radio.1.countrycode=840 wireless.1.macclone=disabled radio.1.channel=42 wireless.1.wds=disabled users.1.status=enabled users.1.name=ubnt users.1.password=VvpvCwhccFv6Q httpd.status=enabled httpd.port=80 radio.status=enabled radio.countrycode=840 radio.ratemodule=ath_rate_sample radio.1.status=enabled radio.1.devname=ath0 radio.1.mode=master radio.1.rate.max=54M radio.1.rate.auto=enabled radio.1.ieee_mode=ast radio.1.txpower=19 radio.1.acktimeout=22 radio.1.ack.auto=enabled radio.1.rx_antenna_diversity=disabled radio.1.tx_antenna_diversity=disabled radio.1.rx_antenna=2 radio.1.tx_antenna=2 wireless.status=enabled wireless.1.status=enabled wireless.1.devname=ath0 wireless.1.security=none wireless.1.ssid=RadNet2 wireless.1.hide_ssid=disabled bridge.status=enabled bridge.1.devname=br0 bridge.1.fd=1 bridge.1.port.1.devname=eth0 bridge.1.port.2.devname=ath0 netconf.status=enabled netconf.1.status=enabled netconf.1.devname=eth0 netconf.1.ip=0.0.0.0 netconf.1.netmask=255.255.255.0 netconf.1.up=enabled netconf.1.promisc=enabled netconf.2.status=enabled netconf.2.devname=ath0 netconf.2.ip=0.0.0.0 netconf.2.netmask=255.255.255.0 netconf.2.up=enabled netconf.3.status=enabled netconf.3.devname=br0 netconf.3.ip=64.203.123.37 netconf.3.netmask=255.255.255.240 netconf.3.up=enabled dhcpd.status=disabled dhcpd.1.status=disabled dhcpc.status=disabled dhcpc.1.status=disabled dhcpc.1.devname=br0 route.status=enabled route.1.status=enabled route.1.devname=br0 route.1.gateway=64.203.123.33 route.1.ip=0.0.0.0 route.1.netmask=0 ebtables.status=enabled ebtables.1.status=disabled ebtables.1.cmd=-t nat -A PREROUTING --in-interface ath0 -j arpnat --arpnat-target ACCEPT ebtables.2.status=disabled ebtables.2.cmd=-t nat -A POSTROUTING --out-interface ath0 -j arpnat --arpnat-target ACCEPT ebtables.3.status=enabled ebtables.3.cmd=-t broute -A BROUTING --protocol 0x888e --in-interface ath0 -j DROP resolv.nameserver.2.ip=64.192.0.11 resolv.host.1.status=enabled resolv.host.1.name=RadNet2 ntpclient.status=enabled ntpclient.1.status=enabled ntpclient.1.server=ntp.ucsd.edu aaa.1.wpa=1 aaa.1.wpa.1.pairwise=TKIP CCMP aaa.1.driver=madwifi aaa.1.devname=ath0 aaa.1.br.devname=br0 aaa.1.ssid=RadNet2 aaa.1.wpa.psk=spiffyjuice aaa.1.wpa.key.1.mgmt=WPA-PSK wpasupplicant.device.1.profile= wpasupplicant.profile.1.name= wpasupplicant.profile.1.network.1.key_mgmt.1.name= wpasupplicant.profile.1.network.1.bssid= wpasupplicant.profile.1.network.1.psk=spiffyjuice


I rather hope that this is some sort of embarrassing brain fart on my part, because that will be a lot easier to fix :P

Thanks for any help!

[BeAuMaN]

So uh... any thoughts?

[UBNT-Mike.Ford]

Hey,

I dont see anything blatantly obvious so im asking my engineer's to jump in

Mike

[BeAuMaN]

Ack, that's what I feared.

Well, thanks Mike!

Tell me if you need me to post anything extra (I think I covered everything), or if you need me to PM you their support serial numbers (Though I'm not sure how those are used).

If I don't hear anything, I'll go ahead and bump on Friday.

Thanks again!

[mwalden]

I'm having much the same issue that you were having. We're you ever able to fix the issue? If you were I'd very much appreciate knowing the steps you took to resolve the issue. Thanks!

[BeAuMaN]

As you can see by the dates, this is a newly presented issue.

Hoping to hear back soon from Mike about their engineer's findings.

[UBNT-keba]

First of all I see that you are configured WPA-AES(CCMP) on one side and WPA (both AES(CCMP) and TKIP). Try to set the same at both ends (like WPA-TKIP) for a try

[mwalden]

Whoops. Sorry. I glanced at the date you joined as a user rather than the posting date.

[BeAuMaN]

Oh, I might be in luck, it could be a brainfart. test of both WPA-TKIP PSK worked. I'm assuming I had the station configured to both, UBNT-keba, and the access point to only WPA-AES? (If it was visa versa, then something is still bugged, because when the access point is operating in both, it should accept one or the others)

Doing further testing as I wait for my eggs.

[BeAuMaN]

Set both to WPA-AES. Failed. I'm completely sure both were set (at least at the UI end-user level) to WPA-AES, as I took a screenshot with me. Going to try another WPA2-TKIP next. Note that this takes a while as I have to drive between both points physically.

Uploading settings for confirmation, in case something fishy is going on in configuration that I'm not seeing in the UI.

RadNet1 (station)

users.status=enabled wpasupplicant.profile.1.network.1.ssid=RadNet2 wpasupplicant.profile.1.network.1.pairwise.1.name=CCMP wpasupplicant.profile.1.network.1.proto.1.name=WPA wpasupplicant.device.1.driver=madwifi wpasupplicant.device.1.devname=ath0 ntpclient.1.server=ntp.ucsd.edu ntpclient.1.status=enabled ntpclient.status=enabled resolv.nameserver.2.ip=64.192.0.11 wireless.1.scan_list.status=disabled radio.1.thresh62g=28 radio.1.thresh62b=28 radio.1.thresh62a=28 wireless.1.l2_isolation=enabled netconf.2.allmulti=disabled radio.1.dfs.status= wireless.1.addmtikie=enabled wireless.1.sper=disabled tshaper.status=disabled wireless.1.signal_led4=65 wireless.1.signal_led3=73 wireless.1.signal_led2=80 wireless.1.signal_led1=94 radio.1.ext_antenna=disabled wireless.1.compression=enabled wireless.1.frameburst=enabled wireless.1.fastframes=enabled radio.1.frag=off radio.1.rts=off wireless.1.wmmlevel=-1 wireless.1.wmm=disabled ebtables.3.cmd=-t broute -A BROUTING --protocol 0x888e --in-interface ath0 -j DROP ebtables.3.status=enabled ebtables.2.cmd=-t nat -A POSTROUTING --out-interface ath0 -j arpnat --arpnat-target ACCEPT ebtables.2.status=enabled ebtables.1.cmd=-t nat -A PREROUTING --in-interface ath0 -j arpnat --arpnat-target ACCEPT ebtables.1.status=enabled ebtables.status=enabled route.1.netmask=0 route.1.ip=0.0.0.0 route.1.gateway=64.203.123.33 route.1.devname=br0 route.1.status=enabled route.status=enabled dhcpc.1.devname=br0 dhcpc.1.status=disabled dhcpc.status=disabled dhcpd.1.status=disabled dhcpd.status=disabled netconf.3.up=enabled netconf.3.netmask=255.255.255.240 netconf.3.ip=64.203.123.38 netconf.3.devname=br0 netconf.3.status=enabled netconf.2.up=enabled netconf.2.netmask=255.255.255.0 netconf.2.ip=0.0.0.0 netconf.2.devname=ath0 netconf.2.status=enabled netconf.1.promisc=enabled netconf.1.up=enabled netconf.1.netmask=255.255.255.0 netconf.1.ip=0.0.0.0 netconf.1.devname=eth0 netconf.1.status=enabled netconf.status=enabled bridge.1.port.2.devname=ath0 bridge.1.port.1.devname=eth0 bridge.1.fd=1 bridge.1.devname=br0 bridge.status=enabled wireless.1.hide_ssid=disabled wireless.1.ssid=RadNet2 wireless.1.security=none wireless.1.devname=ath0 wireless.1.status=enabled wireless.status=enabled radio.1.tx_antenna=2 radio.1.rx_antenna=2 radio.1.tx_antenna_diversity=disabled radio.1.rx_antenna_diversity=disabled radio.1.ack.auto=enabled radio.1.acktimeout=22 radio.1.txpower=19 radio.1.ieee_mode=ast radio.1.rate.auto=enabled radio.1.rate.max=54M radio.1.mode=managed radio.1.devname=ath0 radio.1.status=enabled radio.ratemodule=ath_rate_sample radio.countrycode=840 radio.status=enabled httpd.port=80 httpd.status=enabled users.1.password=VvpvCwhccFv6Q users.1.name=ubnt users.1.status=enabled wireless.1.wds=disabled radio.1.channel=36 wireless.1.macclone=disabled radio.1.countrycode=840 radio.1.mcastrate=6M radio.1.clksel=0 radio.1.chanshift=0 wireless.1.authmode=1 wireless.1.ap=00:15:6D:B5:F8:05 wireless.1.mac_acl.status=disabled wireless.1.mac_acl.policy=allow wireless.1.mac_acl.1.status=disabled wireless.1.mac_acl.1.mac= wireless.1.mac_acl.2.status=disabled wireless.1.mac_acl.2.mac= wireless.1.mac_acl.3.status=disabled wireless.1.mac_acl.3.mac= wireless.1.mac_acl.4.status=disabled wireless.1.mac_acl.4.mac= wireless.1.mac_acl.5.status=disabled wireless.1.mac_acl.5.mac= wireless.1.mac_acl.6.status=disabled wireless.1.mac_acl.6.mac= wireless.1.mac_acl.7.status=disabled wireless.1.mac_acl.7.mac= wireless.1.mac_acl.8.status=disabled wireless.1.mac_acl.8.mac= wireless.1.mac_acl.9.status=disabled wireless.1.mac_acl.9.mac= wireless.1.mac_acl.10.status=disabled wireless.1.mac_acl.10.mac= wireless.1.mac_acl.11.status=disabled wireless.1.mac_acl.11.mac= wireless.1.mac_acl.12.status=disabled wireless.1.mac_acl.12.mac= wireless.1.mac_acl.13.status=disabled wireless.1.mac_acl.13.mac= wireless.1.mac_acl.14.status=disabled wireless.1.mac_acl.14.mac= wireless.1.mac_acl.15.status=disabled wireless.1.mac_acl.15.mac= wireless.1.mac_acl.16.status=disabled wireless.1.mac_acl.16.mac= wpasupplicant.status=enabled wpasupplicant.device.1.status=enabled aaa.status=disabled aaa.1.status=disabled aaa.1.wpa=2 aaa.1.wpa.1.pairwise=CCMP aaa.1.driver=madwifi aaa.1.devname=ath0 aaa.1.br.devname=br0 aaa.1.ssid=RadNet1 aaa.1.wpa.psk=spiffyjuice aaa.1.wpa.key.1.mgmt=WPA-PSK wpasupplicant.device.1.profile=WPA-PSK wpasupplicant.profile.1.name=WPA-PSK wpasupplicant.profile.1.network.1.key_mgmt.1.name=WPA-PSK wpasupplicant.profile.1.network.1.bssid=00:15:6D:B5:F8:05 wpasupplicant.profile.1.network.1.psk=spiffyjuice ppp.1.password= ppp.status=disabled iptables.3.status=disabled ppp.1.status=disabled iptables.status=disabled resolv.nameserver.1.ip=64.192.0.10 resolv.nameserver.1.status=enabled resolv.nameserver.2.status=enabled resolv.status=enabled ebtables.50.status=disabled ebtables.51.status=disabled netmode=bridge igmpproxy.status=disabled bridge.1.stp.status=disabled resolv.host.1.status=enabled resolv.host.1.name=RadNet1 dhcpc.1.fallback=192.168.1.20


RadNet2 (AP)

users.status=enabled radio.1.thresh62g=28 radio.1.thresh62b=28 radio.1.thresh62a=28 wireless.1.l2_isolation=disabled netconf.2.allmulti=disabled radio.1.dfs.status= wireless.1.addmtikie=enabled wireless.1.sper=disabled tshaper.status=disabled wireless.1.signal_led4=65 wireless.1.signal_led3=73 wireless.1.signal_led2=80 wireless.1.signal_led1=94 radio.1.ext_antenna=disabled wireless.1.compression=enabled wireless.1.frameburst=enabled wireless.1.fastframes=enabled radio.1.frag=off radio.1.rts=off wireless.1.wmmlevel=-1 wireless.1.wmm=disabled bridge.1.stp.status=disabled igmpproxy.status=disabled netmode=bridge ebtables.51.status=disabled ebtables.50.status=disabled resolv.status=enabled resolv.nameserver.2.status=enabled resolv.nameserver.1.status=enabled resolv.nameserver.1.ip=64.192.0.10 iptables.status=disabled ppp.1.status=disabled iptables.3.status=disabled ppp.status=disabled ppp.1.password= wpasupplicant.device.1.status=disabled wpasupplicant.status=disabled aaa.1.status=enabled aaa.status=enabled wireless.1.mac_acl.16.mac= wireless.1.mac_acl.16.status=disabled wireless.1.mac_acl.15.mac= wireless.1.mac_acl.15.status=disabled wireless.1.mac_acl.14.mac= wireless.1.mac_acl.14.status=disabled wireless.1.mac_acl.13.mac= wireless.1.mac_acl.13.status=disabled wireless.1.mac_acl.12.mac= wireless.1.mac_acl.12.status=disabled wireless.1.mac_acl.11.mac= wireless.1.mac_acl.11.status=disabled wireless.1.mac_acl.10.mac= wireless.1.mac_acl.10.status=disabled wireless.1.mac_acl.9.mac= wireless.1.mac_acl.9.status=disabled wireless.1.mac_acl.8.mac= wireless.1.mac_acl.8.status=disabled wireless.1.mac_acl.7.mac= wireless.1.mac_acl.7.status=disabled wireless.1.mac_acl.6.mac= wireless.1.mac_acl.6.status=disabled wireless.1.mac_acl.5.mac= wireless.1.mac_acl.5.status=disabled wireless.1.mac_acl.4.mac= wireless.1.mac_acl.4.status=disabled wireless.1.mac_acl.3.mac= wireless.1.mac_acl.3.status=disabled wireless.1.mac_acl.2.mac= wireless.1.mac_acl.2.status=disabled wireless.1.mac_acl.1.mac= wireless.1.mac_acl.1.status=disabled wireless.1.mac_acl.policy=allow wireless.1.mac_acl.status=disabled wireless.1.ap= wireless.1.authmode=1 radio.1.chanshift=0 radio.1.clksel=0 radio.1.mcastrate=6M radio.1.countrycode=840 wireless.1.macclone=disabled radio.1.channel=42 wireless.1.wds=disabled users.1.status=enabled users.1.name=ubnt users.1.password=VvpvCwhccFv6Q httpd.status=enabled httpd.port=80 radio.status=enabled radio.countrycode=840 radio.ratemodule=ath_rate_sample radio.1.status=enabled radio.1.devname=ath0 radio.1.mode=master radio.1.rate.max=54M radio.1.rate.auto=enabled radio.1.ieee_mode=ast radio.1.txpower=19 radio.1.acktimeout=22 radio.1.ack.auto=enabled radio.1.rx_antenna_diversity=disabled radio.1.tx_antenna_diversity=disabled radio.1.rx_antenna=2 radio.1.tx_antenna=2 wireless.status=enabled wireless.1.status=enabled wireless.1.devname=ath0 wireless.1.security=none wireless.1.ssid=RadNet2 wireless.1.hide_ssid=disabled bridge.status=enabled bridge.1.devname=br0 bridge.1.fd=1 bridge.1.port.1.devname=eth0 bridge.1.port.2.devname=ath0 netconf.status=enabled netconf.1.status=enabled netconf.1.devname=eth0 netconf.1.ip=0.0.0.0 netconf.1.netmask=255.255.255.0 netconf.1.up=enabled netconf.1.promisc=enabled netconf.2.status=enabled netconf.2.devname=ath0 netconf.2.ip=0.0.0.0 netconf.2.netmask=255.255.255.0 netconf.2.up=enabled netconf.3.status=enabled netconf.3.devname=br0 netconf.3.ip=64.203.123.37 netconf.3.netmask=255.255.255.240 netconf.3.up=enabled dhcpd.status=disabled dhcpd.1.status=disabled dhcpc.status=disabled dhcpc.1.status=disabled dhcpc.1.devname=br0 route.status=enabled route.1.status=enabled route.1.devname=br0 route.1.gateway=64.203.123.33 route.1.ip=0.0.0.0 route.1.netmask=0 ebtables.status=enabled ebtables.1.status=disabled ebtables.1.cmd=-t nat -A PREROUTING --in-interface ath0 -j arpnat --arpnat-target ACCEPT ebtables.2.status=disabled ebtables.2.cmd=-t nat -A POSTROUTING --out-interface ath0 -j arpnat --arpnat-target ACCEPT ebtables.3.status=enabled ebtables.3.cmd=-t broute -A BROUTING --protocol 0x888e --in-interface ath0 -j DROP resolv.nameserver.2.ip=64.192.0.11 resolv.host.1.status=enabled resolv.host.1.name=RadNet2 ntpclient.status=enabled ntpclient.1.status=enabled ntpclient.1.server=ntp.ucsd.edu aaa.1.wpa=1 aaa.1.wpa.1.pairwise=CCMP aaa.1.driver=madwifi aaa.1.devname=ath0 aaa.1.br.devname=br0 aaa.1.ssid=RadNet2 aaa.1.wpa.psk=spiffyjuice aaa.1.wpa.key.1.mgmt=WPA-PSK wpasupplicant.device.1.profile= wpasupplicant.profile.1.name= wpasupplicant.profile.1.network.1.key_mgmt.1.name= wpasupplicant.profile.1.network.1.bssid= wpasupplicant.profile.1.network.1.psk=spiffyjuice

[BeAuMaN]

WPA2-TKIP successful. Will attempt WPA2-AES next. Usually I "zero" the devices first by switching them over to no protection before switching them over to the new protection. 30 second rule applies.

Submitting config.

my current method is:
Change over AP
Change over Station
Apply Changes to AP
Wait 30 seconds
Apply Changes to Station
Wait 30 seconds
Attempt to connect to AP and google.


RadNet1 (station)

users.status=enabled wpasupplicant.profile.1.network.1.ssid=RadNet2 wpasupplicant.profile.1.network.1.pairwise.1.name=TKIP wpasupplicant.profile.1.network.1.proto.1.name=RSN wpasupplicant.device.1.driver=madwifi wpasupplicant.device.1.devname=ath0 ntpclient.1.server=ntp.ucsd.edu ntpclient.1.status=enabled ntpclient.status=enabled resolv.nameserver.2.ip=64.192.0.11 wireless.1.scan_list.status=disabled radio.1.thresh62g=28 radio.1.thresh62b=28 radio.1.thresh62a=28 wireless.1.l2_isolation=enabled netconf.2.allmulti=disabled radio.1.dfs.status= wireless.1.addmtikie=enabled wireless.1.sper=disabled tshaper.status=disabled wireless.1.signal_led4=65 wireless.1.signal_led3=73 wireless.1.signal_led2=80 wireless.1.signal_led1=94 radio.1.ext_antenna=disabled wireless.1.compression=enabled wireless.1.frameburst=enabled wireless.1.fastframes=enabled radio.1.frag=off radio.1.rts=off wireless.1.wmmlevel=-1 wireless.1.wmm=disabled ebtables.3.cmd=-t broute -A BROUTING --protocol 0x888e --in-interface ath0 -j DROP ebtables.3.status=enabled ebtables.2.cmd=-t nat -A POSTROUTING --out-interface ath0 -j arpnat --arpnat-target ACCEPT ebtables.2.status=enabled ebtables.1.cmd=-t nat -A PREROUTING --in-interface ath0 -j arpnat --arpnat-target ACCEPT ebtables.1.status=enabled ebtables.status=enabled route.1.netmask=0 route.1.ip=0.0.0.0 route.1.gateway=64.203.123.33 route.1.devname=br0 route.1.status=enabled route.status=enabled dhcpc.1.devname=br0 dhcpc.1.status=disabled dhcpc.status=disabled dhcpd.1.status=disabled dhcpd.status=disabled netconf.3.up=enabled netconf.3.netmask=255.255.255.240 netconf.3.ip=64.203.123.38 netconf.3.devname=br0 netconf.3.status=enabled netconf.2.up=enabled netconf.2.netmask=255.255.255.0 netconf.2.ip=0.0.0.0 netconf.2.devname=ath0 netconf.2.status=enabled netconf.1.promisc=enabled netconf.1.up=enabled netconf.1.netmask=255.255.255.0 netconf.1.ip=0.0.0.0 netconf.1.devname=eth0 netconf.1.status=enabled netconf.status=enabled bridge.1.port.2.devname=ath0 bridge.1.port.1.devname=eth0 bridge.1.fd=1 bridge.1.devname=br0 bridge.status=enabled wireless.1.hide_ssid=disabled wireless.1.ssid=RadNet2 wireless.1.security=none wireless.1.devname=ath0 wireless.1.status=enabled wireless.status=enabled radio.1.tx_antenna=2 radio.1.rx_antenna=2 radio.1.tx_antenna_diversity=disabled radio.1.rx_antenna_diversity=disabled radio.1.ack.auto=enabled radio.1.acktimeout=22 radio.1.txpower=19 radio.1.ieee_mode=ast radio.1.rate.auto=enabled radio.1.rate.max=54M radio.1.mode=managed radio.1.devname=ath0 radio.1.status=enabled radio.ratemodule=ath_rate_sample radio.countrycode=840 radio.status=enabled httpd.port=80 httpd.status=enabled users.1.password=VvpvCwhccFv6Q users.1.name=ubnt users.1.status=enabled wireless.1.wds=disabled radio.1.channel=36 wireless.1.macclone=disabled radio.1.countrycode=840 radio.1.mcastrate=6M radio.1.clksel=0 radio.1.chanshift=0 wireless.1.authmode=1 wireless.1.ap=00:15:6D:B5:F8:05 wireless.1.mac_acl.status=disabled wireless.1.mac_acl.policy=allow wireless.1.mac_acl.1.status=disabled wireless.1.mac_acl.1.mac= wireless.1.mac_acl.2.status=disabled wireless.1.mac_acl.2.mac= wireless.1.mac_acl.3.status=disabled wireless.1.mac_acl.3.mac= wireless.1.mac_acl.4.status=disabled wireless.1.mac_acl.4.mac= wireless.1.mac_acl.5.status=disabled wireless.1.mac_acl.5.mac= wireless.1.mac_acl.6.status=disabled wireless.1.mac_acl.6.mac= wireless.1.mac_acl.7.status=disabled wireless.1.mac_acl.7.mac= wireless.1.mac_acl.8.status=disabled wireless.1.mac_acl.8.mac= wireless.1.mac_acl.9.status=disabled wireless.1.mac_acl.9.mac= wireless.1.mac_acl.10.status=disabled wireless.1.mac_acl.10.mac= wireless.1.mac_acl.11.status=disabled wireless.1.mac_acl.11.mac= wireless.1.mac_acl.12.status=disabled wireless.1.mac_acl.12.mac= wireless.1.mac_acl.13.status=disabled wireless.1.mac_acl.13.mac= wireless.1.mac_acl.14.status=disabled wireless.1.mac_acl.14.mac= wireless.1.mac_acl.15.status=disabled wireless.1.mac_acl.15.mac= wireless.1.mac_acl.16.status=disabled wireless.1.mac_acl.16.mac= wpasupplicant.status=enabled wpasupplicant.device.1.status=enabled aaa.status=disabled aaa.1.status=disabled aaa.1.wpa=2 aaa.1.wpa.1.pairwise=CCMP aaa.1.driver=madwifi aaa.1.devname=ath0 aaa.1.br.devname=br0 aaa.1.ssid=RadNet1 aaa.1.wpa.psk=spiffyjuice aaa.1.wpa.key.1.mgmt=WPA-PSK wpasupplicant.device.1.profile=WPA-PSK wpasupplicant.profile.1.name=WPA-PSK wpasupplicant.profile.1.network.1.key_mgmt.1.name=WPA-PSK wpasupplicant.profile.1.network.1.bssid=00:15:6D:B5:F8:05 wpasupplicant.profile.1.network.1.psk=spiffyjuice ppp.1.password= ppp.status=disabled iptables.3.status=disabled ppp.1.status=disabled iptables.status=disabled resolv.nameserver.1.ip=64.192.0.10 resolv.nameserver.1.status=enabled resolv.nameserver.2.status=enabled resolv.status=enabled ebtables.50.status=disabled ebtables.51.status=disabled netmode=bridge igmpproxy.status=disabled bridge.1.stp.status=disabled resolv.host.1.status=enabled resolv.host.1.name=RadNet1 dhcpc.1.fallback=192.168.1.20


RadNet2 (AP)

users.status=enabled radio.1.thresh62g=28 radio.1.thresh62b=28 radio.1.thresh62a=28 wireless.1.l2_isolation=disabled netconf.2.allmulti=disabled radio.1.dfs.status= wireless.1.addmtikie=enabled wireless.1.sper=disabled tshaper.status=disabled wireless.1.signal_led4=65 wireless.1.signal_led3=73 wireless.1.signal_led2=80 wireless.1.signal_led1=94 radio.1.ext_antenna=disabled wireless.1.compression=enabled wireless.1.frameburst=enabled wireless.1.fastframes=enabled radio.1.frag=off radio.1.rts=off wireless.1.wmmlevel=-1 wireless.1.wmm=disabled bridge.1.stp.status=disabled igmpproxy.status=disabled netmode=bridge ebtables.51.status=disabled ebtables.50.status=disabled resolv.status=enabled resolv.nameserver.2.status=enabled resolv.nameserver.1.status=enabled resolv.nameserver.1.ip=64.192.0.10 iptables.status=disabled ppp.1.status=disabled iptables.3.status=disabled ppp.status=disabled ppp.1.password= wpasupplicant.device.1.status=disabled wpasupplicant.status=disabled aaa.1.status=enabled aaa.status=enabled wireless.1.mac_acl.16.mac= wireless.1.mac_acl.16.status=disabled wireless.1.mac_acl.15.mac= wireless.1.mac_acl.15.status=disabled wireless.1.mac_acl.14.mac= wireless.1.mac_acl.14.status=disabled wireless.1.mac_acl.13.mac= wireless.1.mac_acl.13.status=disabled wireless.1.mac_acl.12.mac= wireless.1.mac_acl.12.status=disabled wireless.1.mac_acl.11.mac= wireless.1.mac_acl.11.status=disabled wireless.1.mac_acl.10.mac= wireless.1.mac_acl.10.status=disabled wireless.1.mac_acl.9.mac= wireless.1.mac_acl.9.status=disabled wireless.1.mac_acl.8.mac= wireless.1.mac_acl.8.status=disabled wireless.1.mac_acl.7.mac= wireless.1.mac_acl.7.status=disabled wireless.1.mac_acl.6.mac= wireless.1.mac_acl.6.status=disabled wireless.1.mac_acl.5.mac= wireless.1.mac_acl.5.status=disabled wireless.1.mac_acl.4.mac= wireless.1.mac_acl.4.status=disabled wireless.1.mac_acl.3.mac= wireless.1.mac_acl.3.status=disabled wireless.1.mac_acl.2.mac= wireless.1.mac_acl.2.status=disabled wireless.1.mac_acl.1.mac= wireless.1.mac_acl.1.status=disabled wireless.1.mac_acl.policy=allow wireless.1.mac_acl.status=disabled wireless.1.ap= wireless.1.authmode=1 radio.1.chanshift=0 radio.1.clksel=0 radio.1.mcastrate=6M radio.1.countrycode=840 wireless.1.macclone=disabled radio.1.channel=42 wireless.1.wds=disabled users.1.status=enabled users.1.name=ubnt users.1.password=VvpvCwhccFv6Q httpd.status=enabled httpd.port=80 radio.status=enabled radio.countrycode=840 radio.ratemodule=ath_rate_sample radio.1.status=enabled radio.1.devname=ath0 radio.1.mode=master radio.1.rate.max=54M radio.1.rate.auto=enabled radio.1.ieee_mode=ast radio.1.txpower=19 radio.1.acktimeout=22 radio.1.ack.auto=enabled radio.1.rx_antenna_diversity=disabled radio.1.tx_antenna_diversity=disabled radio.1.rx_antenna=2 radio.1.tx_antenna=2 wireless.status=enabled wireless.1.status=enabled wireless.1.devname=ath0 wireless.1.security=none wireless.1.ssid=RadNet2 wireless.1.hide_ssid=disabled bridge.status=enabled bridge.1.devname=br0 bridge.1.fd=1 bridge.1.port.1.devname=eth0 bridge.1.port.2.devname=ath0 netconf.status=enabled netconf.1.status=enabled netconf.1.devname=eth0 netconf.1.ip=0.0.0.0 netconf.1.netmask=255.255.255.0 netconf.1.up=enabled netconf.1.promisc=enabled netconf.2.status=enabled netconf.2.devname=ath0 netconf.2.ip=0.0.0.0 netconf.2.netmask=255.255.255.0 netconf.2.up=enabled netconf.3.status=enabled netconf.3.devname=br0 netconf.3.ip=64.203.123.37 netconf.3.netmask=255.255.255.240 netconf.3.up=enabled dhcpd.status=disabled dhcpd.1.status=disabled dhcpc.status=disabled dhcpc.1.status=disabled dhcpc.1.devname=br0 route.status=enabled route.1.status=enabled route.1.devname=br0 route.1.gateway=64.203.123.33 route.1.ip=0.0.0.0 route.1.netmask=0 ebtables.status=enabled ebtables.1.status=disabled ebtables.1.cmd=-t nat -A PREROUTING --in-interface ath0 -j arpnat --arpnat-target ACCEPT ebtables.2.status=disabled ebtables.2.cmd=-t nat -A POSTROUTING --out-interface ath0 -j arpnat --arpnat-target ACCEPT ebtables.3.status=enabled ebtables.3.cmd=-t broute -A BROUTING --protocol 0x888e --in-interface ath0 -j DROP resolv.nameserver.2.ip=64.192.0.11 resolv.host.1.status=enabled resolv.host.1.name=RadNet2 ntpclient.status=enabled ntpclient.1.status=enabled ntpclient.1.server=ntp.ucsd.edu aaa.1.wpa=2 aaa.1.wpa.1.pairwise=TKIP aaa.1.driver=madwifi aaa.1.devname=ath0 aaa.1.br.devname=br0 aaa.1.ssid=RadNet2 aaa.1.wpa.psk=spiffyjuice aaa.1.wpa.key.1.mgmt=WPA-PSK wpasupplicant.device.1.profile= wpasupplicant.profile.1.name= wpasupplicant.profile.1.network.1.key_mgmt.1.name= wpasupplicant.profile.1.network.1.bssid= wpasupplicant.profile.1.network.1.psk=spiffyjuice

[BeAuMaN]

WPA2-AES failed. Will attempt WEP next.

Thoughts: What's the operating temperature range of the NanoStation 5s? Being that Ubiquiti Networks is in California, you should be aware of the rather hot temperatures in the Central Valley of California.

We're getting temperatures between 95 and 110 degrees Fahrenheit this week.

I bring up the aspect of temperature because as far as I'm aware, AES is a hardware-intensive encryption while TKIP is software intensive (One requires beefier hardware, the other adds excess overhead to the network). If AES is requiring more hardware power, and the heat down here is getting to the unit, that may cause it to overheat and possibly not process everything correctly?

I figured I'd take a shot at a random theory. I should also mention that my station, despite not being able to connect to the AP's UI or internet, is getting full signal to the AP, as well as detecting it in Site Survey.

Anyhoo, config for both units under WPA2-AES.

RadNet1 (station)

users.status=enabled wpasupplicant.profile.1.network.1.ssid=RadNet2 wpasupplicant.profile.1.network.1.pairwise.1.name=CCMP wpasupplicant.profile.1.network.1.proto.1.name=RSN wpasupplicant.device.1.driver=madwifi wpasupplicant.device.1.devname=ath0 ntpclient.1.server=ntp.ucsd.edu ntpclient.1.status=enabled ntpclient.status=enabled resolv.nameserver.2.ip=64.192.0.11 wireless.1.scan_list.status=disabled radio.1.thresh62g=28 radio.1.thresh62b=28 radio.1.thresh62a=28 wireless.1.l2_isolation=enabled netconf.2.allmulti=disabled radio.1.dfs.status= wireless.1.addmtikie=enabled wireless.1.sper=disabled tshaper.status=disabled wireless.1.signal_led4=65 wireless.1.signal_led3=73 wireless.1.signal_led2=80 wireless.1.signal_led1=94 radio.1.ext_antenna=disabled wireless.1.compression=enabled wireless.1.frameburst=enabled wireless.1.fastframes=enabled radio.1.frag=off radio.1.rts=off wireless.1.wmmlevel=-1 wireless.1.wmm=disabled ebtables.3.cmd=-t broute -A BROUTING --protocol 0x888e --in-interface ath0 -j DROP ebtables.3.status=enabled ebtables.2.cmd=-t nat -A POSTROUTING --out-interface ath0 -j arpnat --arpnat-target ACCEPT ebtables.2.status=enabled ebtables.1.cmd=-t nat -A PREROUTING --in-interface ath0 -j arpnat --arpnat-target ACCEPT ebtables.1.status=enabled ebtables.status=enabled route.1.netmask=0 route.1.ip=0.0.0.0 route.1.gateway=64.203.123.33 route.1.devname=br0 route.1.status=enabled route.status=enabled dhcpc.1.devname=br0 dhcpc.1.status=disabled dhcpc.status=disabled dhcpd.1.status=disabled dhcpd.status=disabled netconf.3.up=enabled netconf.3.netmask=255.255.255.240 netconf.3.ip=64.203.123.38 netconf.3.devname=br0 netconf.3.status=enabled netconf.2.up=enabled netconf.2.netmask=255.255.255.0 netconf.2.ip=0.0.0.0 netconf.2.devname=ath0 netconf.2.status=enabled netconf.1.promisc=enabled netconf.1.up=enabled netconf.1.netmask=255.255.255.0 netconf.1.ip=0.0.0.0 netconf.1.devname=eth0 netconf.1.status=enabled netconf.status=enabled bridge.1.port.2.devname=ath0 bridge.1.port.1.devname=eth0 bridge.1.fd=1 bridge.1.devname=br0 bridge.status=enabled wireless.1.hide_ssid=disabled wireless.1.ssid=RadNet2 wireless.1.security=none wireless.1.devname=ath0 wireless.1.status=enabled wireless.status=enabled radio.1.tx_antenna=2 radio.1.rx_antenna=2 radio.1.tx_antenna_diversity=disabled radio.1.rx_antenna_diversity=disabled radio.1.ack.auto=enabled radio.1.acktimeout=22 radio.1.txpower=19 radio.1.ieee_mode=ast radio.1.rate.auto=enabled radio.1.rate.max=54M radio.1.mode=managed radio.1.devname=ath0 radio.1.status=enabled radio.ratemodule=ath_rate_sample radio.countrycode=840 radio.status=enabled httpd.port=80 httpd.status=enabled users.1.password=VvpvCwhccFv6Q users.1.name=ubnt users.1.status=enabled wireless.1.wds=disabled radio.1.channel=36 wireless.1.macclone=disabled radio.1.countrycode=840 radio.1.mcastrate=6M radio.1.clksel=0 radio.1.chanshift=0 wireless.1.authmode=1 wireless.1.ap=00:15:6D:B5:F8:05 wireless.1.mac_acl.status=disabled wireless.1.mac_acl.policy=allow wireless.1.mac_acl.1.status=disabled wireless.1.mac_acl.1.mac= wireless.1.mac_acl.2.status=disabled wireless.1.mac_acl.2.mac= wireless.1.mac_acl.3.status=disabled wireless.1.mac_acl.3.mac= wireless.1.mac_acl.4.status=disabled wireless.1.mac_acl.4.mac= wireless.1.mac_acl.5.status=disabled wireless.1.mac_acl.5.mac= wireless.1.mac_acl.6.status=disabled wireless.1.mac_acl.6.mac= wireless.1.mac_acl.7.status=disabled wireless.1.mac_acl.7.mac= wireless.1.mac_acl.8.status=disabled wireless.1.mac_acl.8.mac= wireless.1.mac_acl.9.status=disabled wireless.1.mac_acl.9.mac= wireless.1.mac_acl.10.status=disabled wireless.1.mac_acl.10.mac= wireless.1.mac_acl.11.status=disabled wireless.1.mac_acl.11.mac= wireless.1.mac_acl.12.status=disabled wireless.1.mac_acl.12.mac= wireless.1.mac_acl.13.status=disabled wireless.1.mac_acl.13.mac= wireless.1.mac_acl.14.status=disabled wireless.1.mac_acl.14.mac= wireless.1.mac_acl.15.status=disabled wireless.1.mac_acl.15.mac= wireless.1.mac_acl.16.status=disabled wireless.1.mac_acl.16.mac= wpasupplicant.status=enabled wpasupplicant.device.1.status=enabled aaa.status=disabled aaa.1.status=disabled aaa.1.wpa=2 aaa.1.wpa.1.pairwise=CCMP aaa.1.driver=madwifi aaa.1.devname=ath0 aaa.1.br.devname=br0 aaa.1.ssid=RadNet1 aaa.1.wpa.psk=spiffyjuice aaa.1.wpa.key.1.mgmt=WPA-PSK wpasupplicant.device.1.profile=WPA-PSK wpasupplicant.profile.1.name=WPA-PSK wpasupplicant.profile.1.network.1.key_mgmt.1.name=WPA-PSK wpasupplicant.profile.1.network.1.bssid=00:15:6D:B5:F8:05 wpasupplicant.profile.1.network.1.psk=spiffyjuice ppp.1.password= ppp.status=disabled iptables.3.status=disabled ppp.1.status=disabled iptables.status=disabled resolv.nameserver.1.ip=64.192.0.10 resolv.nameserver.1.status=enabled resolv.nameserver.2.status=enabled resolv.status=enabled ebtables.50.status=disabled ebtables.51.status=disabled netmode=bridge igmpproxy.status=disabled bridge.1.stp.status=disabled resolv.host.1.status=enabled resolv.host.1.name=RadNet1 dhcpc.1.fallback=192.168.1.20


RadNet2 (AP)

users.status=enabled radio.1.thresh62g=28 radio.1.thresh62b=28 radio.1.thresh62a=28 wireless.1.l2_isolation=disabled netconf.2.allmulti=disabled radio.1.dfs.status= wireless.1.addmtikie=enabled wireless.1.sper=disabled tshaper.status=disabled wireless.1.signal_led4=65 wireless.1.signal_led3=73 wireless.1.signal_led2=80 wireless.1.signal_led1=94 radio.1.ext_antenna=disabled wireless.1.compression=enabled wireless.1.frameburst=enabled wireless.1.fastframes=enabled radio.1.frag=off radio.1.rts=off wireless.1.wmmlevel=-1 wireless.1.wmm=disabled bridge.1.stp.status=disabled igmpproxy.status=disabled netmode=bridge ebtables.51.status=disabled ebtables.50.status=disabled resolv.status=enabled resolv.nameserver.2.status=enabled resolv.nameserver.1.status=enabled resolv.nameserver.1.ip=64.192.0.10 iptables.status=disabled ppp.1.status=disabled iptables.3.status=disabled ppp.status=disabled ppp.1.password= wpasupplicant.device.1.status=disabled wpasupplicant.status=disabled aaa.1.status=enabled aaa.status=enabled wireless.1.mac_acl.16.mac= wireless.1.mac_acl.16.status=disabled wireless.1.mac_acl.15.mac= wireless.1.mac_acl.15.status=disabled wireless.1.mac_acl.14.mac= wireless.1.mac_acl.14.status=disabled wireless.1.mac_acl.13.mac= wireless.1.mac_acl.13.status=disabled wireless.1.mac_acl.12.mac= wireless.1.mac_acl.12.status=disabled wireless.1.mac_acl.11.mac= wireless.1.mac_acl.11.status=disabled wireless.1.mac_acl.10.mac= wireless.1.mac_acl.10.status=disabled wireless.1.mac_acl.9.mac= wireless.1.mac_acl.9.status=disabled wireless.1.mac_acl.8.mac= wireless.1.mac_acl.8.status=disabled wireless.1.mac_acl.7.mac= wireless.1.mac_acl.7.status=disabled wireless.1.mac_acl.6.mac= wireless.1.mac_acl.6.status=disabled wireless.1.mac_acl.5.mac= wireless.1.mac_acl.5.status=disabled wireless.1.mac_acl.4.mac= wireless.1.mac_acl.4.status=disabled wireless.1.mac_acl.3.mac= wireless.1.mac_acl.3.status=disabled wireless.1.mac_acl.2.mac= wireless.1.mac_acl.2.status=disabled wireless.1.mac_acl.1.mac= wireless.1.mac_acl.1.status=disabled wireless.1.mac_acl.policy=allow wireless.1.mac_acl.status=disabled wireless.1.ap= wireless.1.authmode=1 radio.1.chanshift=0 radio.1.clksel=0 radio.1.mcastrate=6M radio.1.countrycode=840 wireless.1.macclone=disabled radio.1.channel=42 wireless.1.wds=disabled users.1.status=enabled users.1.name=ubnt users.1.password=VvpvCwhccFv6Q httpd.status=enabled httpd.port=80 radio.status=enabled radio.countrycode=840 radio.ratemodule=ath_rate_sample radio.1.status=enabled radio.1.devname=ath0 radio.1.mode=master radio.1.rate.max=54M radio.1.rate.auto=enabled radio.1.ieee_mode=ast radio.1.txpower=19 radio.1.acktimeout=22 radio.1.ack.auto=enabled radio.1.rx_antenna_diversity=disabled radio.1.tx_antenna_diversity=disabled radio.1.rx_antenna=2 radio.1.tx_antenna=2 wireless.status=enabled wireless.1.status=enabled wireless.1.devname=ath0 wireless.1.security=none wireless.1.ssid=RadNet2 wireless.1.hide_ssid=disabled bridge.status=enabled bridge.1.devname=br0 bridge.1.fd=1 bridge.1.port.1.devname=eth0 bridge.1.port.2.devname=ath0 netconf.status=enabled netconf.1.status=enabled netconf.1.devname=eth0 netconf.1.ip=0.0.0.0 netconf.1.netmask=255.255.255.0 netconf.1.up=enabled netconf.1.promisc=enabled netconf.2.status=enabled netconf.2.devname=ath0 netconf.2.ip=0.0.0.0 netconf.2.netmask=255.255.255.0 netconf.2.up=enabled netconf.3.status=enabled netconf.3.devname=br0 netconf.3.ip=64.203.123.37 netconf.3.netmask=255.255.255.240 netconf.3.up=enabled dhcpd.status=disabled dhcpd.1.status=disabled dhcpc.status=disabled dhcpc.1.status=disabled dhcpc.1.devname=br0 route.status=enabled route.1.status=enabled route.1.devname=br0 route.1.gateway=64.203.123.33 route.1.ip=0.0.0.0 route.1.netmask=0 ebtables.status=enabled ebtables.1.status=disabled ebtables.1.cmd=-t nat -A PREROUTING --in-interface ath0 -j arpnat --arpnat-target ACCEPT ebtables.2.status=disabled ebtables.2.cmd=-t nat -A POSTROUTING --out-interface ath0 -j arpnat --arpnat-target ACCEPT ebtables.3.status=enabled ebtables.3.cmd=-t broute -A BROUTING --protocol 0x888e --in-interface ath0 -j DROP resolv.nameserver.2.ip=64.192.0.11 resolv.host.1.status=enabled resolv.host.1.name=RadNet2 ntpclient.status=enabled ntpclient.1.status=enabled ntpclient.1.server=ntp.ucsd.edu aaa.1.wpa=2 aaa.1.wpa.1.pairwise=CCMP aaa.1.driver=madwifi aaa.1.devname=ath0 aaa.1.br.devname=br0 aaa.1.ssid=RadNet2 aaa.1.wpa.psk=spiffyjuice aaa.1.wpa.key.1.mgmt=WPA-PSK wpasupplicant.device.1.profile= wpasupplicant.profile.1.name= wpasupplicant.profile.1.network.1.key_mgmt.1.name= wpasupplicant.profile.1.network.1.bssid= wpasupplicant.profile.1.network.1.psk=spiffyjuice

[BeAuMaN]

WEP-Open is successful. So far this seems to be isolated to AES on WPA and WPA2. Checking normal WPA next.

Config files for WEP-Open.

RadNet1 (station)

users.status=enabled wireless.1.security.1.key=1111111111 wireless.1.security.default_key=1 dhcpc.1.fallback=192.168.1.20 resolv.host.1.name=RadNet1 resolv.host.1.status=enabled bridge.1.stp.status=disabled igmpproxy.status=disabled netmode=bridge ebtables.51.status=disabled ebtables.50.status=disabled resolv.status=enabled resolv.nameserver.2.status=enabled resolv.nameserver.1.status=enabled resolv.nameserver.1.ip=64.192.0.10 iptables.status=disabled ppp.1.status=disabled iptables.3.status=disabled ppp.status=disabled ppp.1.password= wpasupplicant.profile.1.network.1.psk=spiffyjuice wpasupplicant.profile.1.network.1.bssid=00:15:6D:B5:F8:05 wpasupplicant.profile.1.network.1.key_mgmt.1.name=WPA-PSK wpasupplicant.profile.1.name=WPA-PSK wpasupplicant.device.1.profile=WPA-PSK aaa.1.wpa.key.1.mgmt=WPA-PSK aaa.1.wpa.psk=spiffyjuice aaa.1.ssid=RadNet1 aaa.1.br.devname=br0 aaa.1.devname=ath0 aaa.1.driver=madwifi aaa.1.wpa.1.pairwise=CCMP aaa.1.wpa=2 aaa.1.status=disabled aaa.status=disabled wpasupplicant.device.1.status=disabled wpasupplicant.status=disabled wireless.1.mac_acl.16.mac= wireless.1.mac_acl.16.status=disabled wireless.1.mac_acl.15.mac= wireless.1.mac_acl.15.status=disabled wireless.1.mac_acl.14.mac= wireless.1.mac_acl.14.status=disabled wireless.1.mac_acl.13.mac= wireless.1.mac_acl.13.status=disabled wireless.1.mac_acl.12.mac= wireless.1.mac_acl.12.status=disabled wireless.1.mac_acl.11.mac= wireless.1.mac_acl.11.status=disabled wireless.1.mac_acl.10.mac= wireless.1.mac_acl.10.status=disabled wireless.1.mac_acl.9.mac= wireless.1.mac_acl.9.status=disabled wireless.1.mac_acl.8.mac= wireless.1.mac_acl.8.status=disabled wireless.1.mac_acl.7.mac= wireless.1.mac_acl.7.status=disabled wireless.1.mac_acl.6.mac= wireless.1.mac_acl.6.status=disabled wireless.1.mac_acl.5.mac= wireless.1.mac_acl.5.status=disabled wireless.1.mac_acl.4.mac= wireless.1.mac_acl.4.status=disabled wireless.1.mac_acl.3.mac= wireless.1.mac_acl.3.status=disabled wireless.1.mac_acl.2.mac= wireless.1.mac_acl.2.status=disabled wireless.1.mac_acl.1.mac= wireless.1.mac_acl.1.status=disabled wireless.1.mac_acl.policy=allow wireless.1.mac_acl.status=disabled wireless.1.ap=00:15:6D:B5:F8:05 wireless.1.authmode=1 radio.1.chanshift=0 radio.1.clksel=0 radio.1.mcastrate=6M radio.1.countrycode=840 wireless.1.macclone=disabled radio.1.channel=36 wireless.1.wds=disabled users.1.status=enabled users.1.name=ubnt users.1.password=VvpvCwhccFv6Q httpd.status=enabled httpd.port=80 radio.status=enabled radio.countrycode=840 radio.ratemodule=ath_rate_sample radio.1.status=enabled radio.1.devname=ath0 radio.1.mode=managed radio.1.rate.max=54M radio.1.rate.auto=enabled radio.1.ieee_mode=ast radio.1.txpower=19 radio.1.acktimeout=22 radio.1.ack.auto=enabled radio.1.rx_antenna_diversity=disabled radio.1.tx_antenna_diversity=disabled radio.1.rx_antenna=2 radio.1.tx_antenna=2 wireless.status=enabled wireless.1.status=enabled wireless.1.devname=ath0 wireless.1.security=wep64 wireless.1.ssid=RadNet2 wireless.1.hide_ssid=disabled bridge.status=enabled bridge.1.devname=br0 bridge.1.fd=1 bridge.1.port.1.devname=eth0 bridge.1.port.2.devname=ath0 netconf.status=enabled netconf.1.status=enabled netconf.1.devname=eth0 netconf.1.ip=0.0.0.0 netconf.1.netmask=255.255.255.0 netconf.1.up=enabled netconf.1.promisc=enabled netconf.2.status=enabled netconf.2.devname=ath0 netconf.2.ip=0.0.0.0 netconf.2.netmask=255.255.255.0 netconf.2.up=enabled netconf.3.status=enabled netconf.3.devname=br0 netconf.3.ip=64.203.123.38 netconf.3.netmask=255.255.255.240 netconf.3.up=enabled dhcpd.status=disabled dhcpd.1.status=disabled dhcpc.status=disabled dhcpc.1.status=disabled dhcpc.1.devname=br0 route.status=enabled route.1.status=enabled route.1.devname=br0 route.1.gateway=64.203.123.33 route.1.ip=0.0.0.0 route.1.netmask=0 ebtables.status=enabled ebtables.1.status=enabled ebtables.1.cmd=-t nat -A PREROUTING --in-interface ath0 -j arpnat --arpnat-target ACCEPT ebtables.2.status=enabled ebtables.2.cmd=-t nat -A POSTROUTING --out-interface ath0 -j arpnat --arpnat-target ACCEPT ebtables.3.status=enabled ebtables.3.cmd=-t broute -A BROUTING --protocol 0x888e --in-interface ath0 -j DROP wireless.1.wmm=disabled wireless.1.wmmlevel=-1 radio.1.rts=off radio.1.frag=off wireless.1.fastframes=enabled wireless.1.frameburst=enabled wireless.1.compression=enabled radio.1.ext_antenna=disabled wireless.1.signal_led1=94 wireless.1.signal_led2=80 wireless.1.signal_led3=73 wireless.1.signal_led4=65 tshaper.status=disabled wireless.1.sper=disabled wireless.1.addmtikie=enabled radio.1.dfs.status= netconf.2.allmulti=disabled wireless.1.l2_isolation=enabled radio.1.thresh62a=28 radio.1.thresh62b=28 radio.1.thresh62g=28 wireless.1.scan_list.status=disabled resolv.nameserver.2.ip=64.192.0.11 ntpclient.status=enabled ntpclient.1.status=enabled ntpclient.1.server=ntp.ucsd.edu wpasupplicant.device.1.devname=ath0 wpasupplicant.device.1.driver=madwifi wpasupplicant.profile.1.network.1.proto.1.name=RSN wpasupplicant.profile.1.network.1.pairwise.1.name=CCMP wpasupplicant.profile.1.network.1.ssid=RadNet2


RadNet2 (AP)

users.status=enabled radio.1.thresh62g=28 radio.1.thresh62b=28 radio.1.thresh62a=28 wireless.1.l2_isolation=disabled netconf.2.allmulti=disabled radio.1.dfs.status= wireless.1.addmtikie=enabled wireless.1.sper=disabled tshaper.status=disabled wireless.1.signal_led4=65 wireless.1.signal_led3=73 wireless.1.signal_led2=80 wireless.1.signal_led1=94 radio.1.ext_antenna=disabled wireless.1.compression=enabled wireless.1.frameburst=enabled wireless.1.fastframes=enabled radio.1.frag=off radio.1.rts=off wireless.1.wmmlevel=-1 wireless.1.wmm=disabled bridge.1.stp.status=disabled igmpproxy.status=disabled netmode=bridge ebtables.51.status=disabled ebtables.50.status=disabled resolv.status=enabled resolv.nameserver.2.status=enabled resolv.nameserver.1.status=enabled resolv.nameserver.1.ip=64.192.0.10 iptables.status=disabled ppp.1.status=disabled iptables.3.status=disabled ppp.status=disabled ppp.1.password= wpasupplicant.device.1.status=disabled wpasupplicant.status=disabled aaa.1.status=disabled aaa.status=disabled wireless.1.mac_acl.16.mac= wireless.1.mac_acl.16.status=disabled wireless.1.mac_acl.15.mac= wireless.1.mac_acl.15.status=disabled wireless.1.mac_acl.14.mac= wireless.1.mac_acl.14.status=disabled wireless.1.mac_acl.13.mac= wireless.1.mac_acl.13.status=disabled wireless.1.mac_acl.12.mac= wireless.1.mac_acl.12.status=disabled wireless.1.mac_acl.11.mac= wireless.1.mac_acl.11.status=disabled wireless.1.mac_acl.10.mac= wireless.1.mac_acl.10.status=disabled wireless.1.mac_acl.9.mac= wireless.1.mac_acl.9.status=disabled wireless.1.mac_acl.8.mac= wireless.1.mac_acl.8.status=disabled wireless.1.mac_acl.7.mac= wireless.1.mac_acl.7.status=disabled wireless.1.mac_acl.6.mac= wireless.1.mac_acl.6.status=disabled wireless.1.mac_acl.5.mac= wireless.1.mac_acl.5.status=disabled wireless.1.mac_acl.4.mac= wireless.1.mac_acl.4.status=disabled wireless.1.mac_acl.3.mac= wireless.1.mac_acl.3.status=disabled wireless.1.mac_acl.2.mac= wireless.1.mac_acl.2.status=disabled wireless.1.mac_acl.1.mac= wireless.1.mac_acl.1.status=disabled wireless.1.mac_acl.policy=allow wireless.1.mac_acl.status=disabled wireless.1.ap= wireless.1.authmode=1 radio.1.chanshift=0 radio.1.clksel=0 radio.1.mcastrate=6M radio.1.countrycode=840 wireless.1.macclone=disabled radio.1.channel=42 wireless.1.wds=disabled users.1.status=enabled users.1.name=ubnt users.1.password=VvpvCwhccFv6Q httpd.status=enabled httpd.port=80 radio.status=enabled radio.countrycode=840 radio.ratemodule=ath_rate_sample radio.1.status=enabled radio.1.devname=ath0 radio.1.mode=master radio.1.rate.max=54M radio.1.rate.auto=enabled radio.1.ieee_mode=ast radio.1.txpower=19 radio.1.acktimeout=22 radio.1.ack.auto=enabled radio.1.rx_antenna_diversity=disabled radio.1.tx_antenna_diversity=disabled radio.1.rx_antenna=2 radio.1.tx_antenna=2 wireless.status=enabled wireless.1.status=enabled wireless.1.devname=ath0 wireless.1.security=wep64 wireless.1.ssid=RadNet2 wireless.1.hide_ssid=disabled bridge.status=enabled bridge.1.devname=br0 bridge.1.fd=1 bridge.1.port.1.devname=eth0 bridge.1.port.2.devname=ath0 netconf.status=enabled netconf.1.status=enabled netconf.1.devname=eth0 netconf.1.ip=0.0.0.0 netconf.1.netmask=255.255.255.0 netconf.1.up=enabled netconf.1.promisc=enabled netconf.2.status=enabled netconf.2.devname=ath0 netconf.2.ip=0.0.0.0 netconf.2.netmask=255.255.255.0 netconf.2.up=enabled netconf.3.status=enabled netconf.3.devname=br0 netconf.3.ip=64.203.123.37 netconf.3.netmask=255.255.255.240 netconf.3.up=enabled dhcpd.status=disabled dhcpd.1.status=disabled dhcpc.status=disabled dhcpc.1.status=disabled dhcpc.1.devname=br0 route.status=enabled route.1.status=enabled route.1.devname=br0 route.1.gateway=64.203.123.33 route.1.ip=0.0.0.0 route.1.netmask=0 ebtables.status=enabled ebtables.1.status=disabled ebtables.1.cmd=-t nat -A PREROUTING --in-interface ath0 -j arpnat --arpnat-target ACCEPT ebtables.2.status=disabled ebtables.2.cmd=-t nat -A POSTROUTING --out-interface ath0 -j arpnat --arpnat-target ACCEPT ebtables.3.status=disabled ebtables.3.cmd=-t broute -A BROUTING --protocol 0x888e --in-interface ath0 -j DROP resolv.nameserver.2.ip=64.192.0.11 resolv.host.1.status=enabled resolv.host.1.name=RadNet2 ntpclient.status=enabled ntpclient.1.status=enabled ntpclient.1.server=ntp.ucsd.edu aaa.1.wpa=2 aaa.1.wpa.1.pairwise=CCMP aaa.1.driver=madwifi aaa.1.devname=ath0 aaa.1.br.devname=br0 aaa.1.ssid=RadNet2 aaa.1.wpa.psk=spiffyjuice aaa.1.wpa.key.1.mgmt=WPA-PSK wpasupplicant.device.1.profile= wpasupplicant.profile.1.name= wpasupplicant.profile.1.network.1.key_mgmt.1.name= wpasupplicant.profile.1.network.1.bssid= wpasupplicant.profile.1.network.1.psk=spiffyjuice wireless.1.security.default_key=1 wireless.1.security.1.key=1111111111

[BeAuMaN]

Standard WPA-PSK (As in, not choosing WPA-AES or WPA-TKIP, but just WPA) fails. Does it choose AES by default?

Testing WPA2-PSK next, as that's the last item on the list.
Once again, here's config files for standard WPA-PSK.

RadNet1 (station)

users.status=enabled wpasupplicant.profile.1.network.1.ssid=RadNet2 wpasupplicant.profile.1.network.1.pairwise.1.name=TKIP CCMP wpasupplicant.profile.1.network.1.proto.1.name=WPA wpasupplicant.device.1.driver=madwifi wpasupplicant.device.1.devname=ath0 ntpclient.1.server=ntp.ucsd.edu ntpclient.1.status=enabled ntpclient.status=enabled resolv.nameserver.2.ip=64.192.0.11 wireless.1.scan_list.status=disabled radio.1.thresh62g=28 radio.1.thresh62b=28 radio.1.thresh62a=28 wireless.1.l2_isolation=enabled netconf.2.allmulti=disabled radio.1.dfs.status= wireless.1.addmtikie=enabled wireless.1.sper=disabled tshaper.status=disabled wireless.1.signal_led4=65 wireless.1.signal_led3=73 wireless.1.signal_led2=80 wireless.1.signal_led1=94 radio.1.ext_antenna=disabled wireless.1.compression=enabled wireless.1.frameburst=enabled wireless.1.fastframes=enabled radio.1.frag=off radio.1.rts=off wireless.1.wmmlevel=-1 wireless.1.wmm=disabled ebtables.3.cmd=-t broute -A BROUTING --protocol 0x888e --in-interface ath0 -j DROP ebtables.3.status=enabled ebtables.2.cmd=-t nat -A POSTROUTING --out-interface ath0 -j arpnat --arpnat-target ACCEPT ebtables.2.status=enabled ebtables.1.cmd=-t nat -A PREROUTING --in-interface ath0 -j arpnat --arpnat-target ACCEPT ebtables.1.status=enabled ebtables.status=enabled route.1.netmask=0 route.1.ip=0.0.0.0 route.1.gateway=64.203.123.33 route.1.devname=br0 route.1.status=enabled route.status=enabled dhcpc.1.devname=br0 dhcpc.1.status=disabled dhcpc.status=disabled dhcpd.1.status=disabled dhcpd.status=disabled netconf.3.up=enabled netconf.3.netmask=255.255.255.240 netconf.3.ip=64.203.123.38 netconf.3.devname=br0 netconf.3.status=enabled netconf.2.up=enabled netconf.2.netmask=255.255.255.0 netconf.2.ip=0.0.0.0 netconf.2.devname=ath0 netconf.2.status=enabled netconf.1.promisc=enabled netconf.1.up=enabled netconf.1.netmask=255.255.255.0 netconf.1.ip=0.0.0.0 netconf.1.devname=eth0 netconf.1.status=enabled netconf.status=enabled bridge.1.port.2.devname=ath0 bridge.1.port.1.devname=eth0 bridge.1.fd=1 bridge.1.devname=br0 bridge.status=enabled wireless.1.hide_ssid=disabled wireless.1.ssid=RadNet2 wireless.1.security=none wireless.1.devname=ath0 wireless.1.status=enabled wireless.status=enabled radio.1.tx_antenna=2 radio.1.rx_antenna=2 radio.1.tx_antenna_diversity=disabled radio.1.rx_antenna_diversity=disabled radio.1.ack.auto=enabled radio.1.acktimeout=22 radio.1.txpower=19 radio.1.ieee_mode=ast radio.1.rate.auto=enabled radio.1.rate.max=54M radio.1.mode=managed radio.1.devname=ath0 radio.1.status=enabled radio.ratemodule=ath_rate_sample radio.countrycode=840 radio.status=enabled httpd.port=80 httpd.status=enabled users.1.password=VvpvCwhccFv6Q users.1.name=ubnt users.1.status=enabled wireless.1.wds=disabled radio.1.channel=36 wireless.1.macclone=disabled radio.1.countrycode=840 radio.1.mcastrate=6M radio.1.clksel=0 radio.1.chanshift=0 wireless.1.authmode=1 wireless.1.ap=00:15:6D:B5:F8:05 wireless.1.mac_acl.status=disabled wireless.1.mac_acl.policy=allow wireless.1.mac_acl.1.status=disabled wireless.1.mac_acl.1.mac= wireless.1.mac_acl.2.status=disabled wireless.1.mac_acl.2.mac= wireless.1.mac_acl.3.status=disabled wireless.1.mac_acl.3.mac= wireless.1.mac_acl.4.status=disabled wireless.1.mac_acl.4.mac= wireless.1.mac_acl.5.status=disabled wireless.1.mac_acl.5.mac= wireless.1.mac_acl.6.status=disabled wireless.1.mac_acl.6.mac= wireless.1.mac_acl.7.status=disabled wireless.1.mac_acl.7.mac= wireless.1.mac_acl.8.status=disabled wireless.1.mac_acl.8.mac= wireless.1.mac_acl.9.status=disabled wireless.1.mac_acl.9.mac= wireless.1.mac_acl.10.status=disabled wireless.1.mac_acl.10.mac= wireless.1.mac_acl.11.status=disabled wireless.1.mac_acl.11.mac= wireless.1.mac_acl.12.status=disabled wireless.1.mac_acl.12.mac= wireless.1.mac_acl.13.status=disabled wireless.1.mac_acl.13.mac= wireless.1.mac_acl.14.status=disabled wireless.1.mac_acl.14.mac= wireless.1.mac_acl.15.status=disabled wireless.1.mac_acl.15.mac= wireless.1.mac_acl.16.status=disabled wireless.1.mac_acl.16.mac= wpasupplicant.status=enabled wpasupplicant.device.1.status=enabled aaa.status=disabled aaa.1.status=disabled aaa.1.wpa=2 aaa.1.wpa.1.pairwise=CCMP aaa.1.driver=madwifi aaa.1.devname=ath0 aaa.1.br.devname=br0 aaa.1.ssid=RadNet1 aaa.1.wpa.psk=spiffyjuice aaa.1.wpa.key.1.mgmt=WPA-PSK wpasupplicant.device.1.profile=WPA-PSK wpasupplicant.profile.1.name=WPA-PSK wpasupplicant.profile.1.network.1.key_mgmt.1.name=WPA-PSK wpasupplicant.profile.1.network.1.bssid=00:15:6D:B5:F8:05 wpasupplicant.profile.1.network.1.psk=spiffyjuice ppp.1.password= ppp.status=disabled iptables.3.status=disabled ppp.1.status=disabled iptables.status=disabled resolv.nameserver.1.ip=64.192.0.10 resolv.nameserver.1.status=enabled resolv.nameserver.2.status=enabled resolv.status=enabled ebtables.50.status=disabled ebtables.51.status=disabled netmode=bridge igmpproxy.status=disabled bridge.1.stp.status=disabled resolv.host.1.status=enabled resolv.host.1.name=RadNet1 dhcpc.1.fallback=192.168.1.20 wireless.1.security.default_key=1 wireless.1.security.1.key=1111111111


RadNet2 (AP)

users.status=enabled wireless.1.security.1.key=1111111111 wireless.1.security.default_key=1 wpasupplicant.profile.1.network.1.psk=spiffyjuice wpasupplicant.profile.1.network.1.bssid= wpasupplicant.profile.1.network.1.key_mgmt.1.name= wpasupplicant.profile.1.name= wpasupplicant.device.1.profile= aaa.1.wpa.key.1.mgmt=WPA-PSK aaa.1.wpa.psk=spiffyjuice aaa.1.ssid=RadNet2 aaa.1.br.devname=br0 aaa.1.devname=ath0 aaa.1.driver=madwifi aaa.1.wpa.1.pairwise=TKIP CCMP aaa.1.wpa=1 ntpclient.1.server=ntp.ucsd.edu ntpclient.1.status=enabled ntpclient.status=enabled resolv.host.1.name=RadNet2 resolv.host.1.status=enabled resolv.nameserver.2.ip=64.192.0.11 ebtables.3.cmd=-t broute -A BROUTING --protocol 0x888e --in-interface ath0 -j DROP ebtables.3.status=enabled ebtables.2.cmd=-t nat -A POSTROUTING --out-interface ath0 -j arpnat --arpnat-target ACCEPT ebtables.2.status=disabled ebtables.1.cmd=-t nat -A PREROUTING --in-interface ath0 -j arpnat --arpnat-target ACCEPT ebtables.1.status=disabled ebtables.status=enabled route.1.netmask=0 route.1.ip=0.0.0.0 route.1.gateway=64.203.123.33 route.1.devname=br0 route.1.status=enabled route.status=enabled dhcpc.1.devname=br0 dhcpc.1.status=disabled dhcpc.status=disabled dhcpd.1.status=disabled dhcpd.status=disabled netconf.3.up=enabled netconf.3.netmask=255.255.255.240 netconf.3.ip=64.203.123.37 netconf.3.devname=br0 netconf.3.status=enabled netconf.2.up=enabled netconf.2.netmask=255.255.255.0 netconf.2.ip=0.0.0.0 netconf.2.devname=ath0 netconf.2.status=enabled netconf.1.promisc=enabled netconf.1.up=enabled netconf.1.netmask=255.255.255.0 netconf.1.ip=0.0.0.0 netconf.1.devname=eth0 netconf.1.status=enabled netconf.status=enabled bridge.1.port.2.devname=ath0 bridge.1.port.1.devname=eth0 bridge.1.fd=1 bridge.1.devname=br0 bridge.status=enabled wireless.1.hide_ssid=disabled wireless.1.ssid=RadNet2 wireless.1.security=none wireless.1.devname=ath0 wireless.1.status=enabled wireless.status=enabled radio.1.tx_antenna=2 radio.1.rx_antenna=2 radio.1.tx_antenna_diversity=disabled radio.1.rx_antenna_diversity=disabled radio.1.ack.auto=enabled radio.1.acktimeout=22 radio.1.txpower=19 radio.1.ieee_mode=ast radio.1.rate.auto=enabled radio.1.rate.max=54M radio.1.mode=master radio.1.devname=ath0 radio.1.status=enabled radio.ratemodule=ath_rate_sample radio.countrycode=840 radio.status=enabled httpd.port=80 httpd.status=enabled users.1.password=VvpvCwhccFv6Q users.1.name=ubnt users.1.status=enabled wireless.1.wds=disabled radio.1.channel=42 wireless.1.macclone=disabled radio.1.countrycode=840 radio.1.mcastrate=6M radio.1.clksel=0 radio.1.chanshift=0 wireless.1.authmode=1 wireless.1.ap= wireless.1.mac_acl.status=disabled wireless.1.mac_acl.policy=allow wireless.1.mac_acl.1.status=disabled wireless.1.mac_acl.1.mac= wireless.1.mac_acl.2.status=disabled wireless.1.mac_acl.2.mac= wireless.1.mac_acl.3.status=disabled wireless.1.mac_acl.3.mac= wireless.1.mac_acl.4.status=disabled wireless.1.mac_acl.4.mac= wireless.1.mac_acl.5.status=disabled wireless.1.mac_acl.5.mac= wireless.1.mac_acl.6.status=disabled wireless.1.mac_acl.6.mac= wireless.1.mac_acl.7.status=disabled wireless.1.mac_acl.7.mac= wireless.1.mac_acl.8.status=disabled wireless.1.mac_acl.8.mac= wireless.1.mac_acl.9.status=disabled wireless.1.mac_acl.9.mac= wireless.1.mac_acl.10.status=disabled wireless.1.mac_acl.10.mac= wireless.1.mac_acl.11.status=disabled wireless.1.mac_acl.11.mac= wireless.1.mac_acl.12.status=disabled wireless.1.mac_acl.12.mac= wireless.1.mac_acl.13.status=disabled wireless.1.mac_acl.13.mac= wireless.1.mac_acl.14.status=disabled wireless.1.mac_acl.14.mac= wireless.1.mac_acl.15.status=disabled wireless.1.mac_acl.15.mac= wireless.1.mac_acl.16.status=disabled wireless.1.mac_acl.16.mac= aaa.status=enabled aaa.1.status=enabled wpasupplicant.status=disabled wpasupplicant.device.1.status=disabled ppp.1.password= ppp.status=disabled iptables.3.status=disabled ppp.1.status=disabled iptables.status=disabled resolv.nameserver.1.ip=64.192.0.10 resolv.nameserver.1.status=enabled resolv.nameserver.2.status=enabled resolv.status=enabled ebtables.50.status=disabled ebtables.51.status=disabled netmode=bridge igmpproxy.status=disabled bridge.1.stp.status=disabled wireless.1.wmm=disabled wireless.1.wmmlevel=-1 radio.1.rts=off radio.1.frag=off wireless.1.fastframes=enabled wireless.1.frameburst=enabled wireless.1.compression=enabled radio.1.ext_antenna=disabled wireless.1.signal_led1=94 wireless.1.signal_led2=80 wireless.1.signal_led3=73 wireless.1.signal_led4=65 tshaper.status=disabled wireless.1.sper=disabled wireless.1.addmtikie=enabled radio.1.dfs.status= netconf.2.allmulti=disabled wireless.1.l2_isolation=disabled radio.1.thresh62a=28 radio.1.thresh62b=28 radio.1.thresh62g=28

[BeAuMaN]

Standard WPA2 (That is, not WPA2-TKIP or WPA2-AES, but just WPA2) failed. Much like the Standard WPA, I'll assume that it defaults to setting up WPA2-AES.

Config files incoming:

RadNet1 (station)

users.status=enabled wireless.1.security.1.key=1111111111 wireless.1.security.default_key=1 dhcpc.1.fallback=192.168.1.20 resolv.host.1.name=RadNet1 resolv.host.1.status=enabled bridge.1.stp.status=disabled igmpproxy.status=disabled netmode=bridge ebtables.51.status=disabled ebtables.50.status=disabled resolv.status=enabled resolv.nameserver.2.status=enabled resolv.nameserver.1.status=enabled resolv.nameserver.1.ip=64.192.0.10 iptables.status=disabled ppp.1.status=disabled iptables.3.status=disabled ppp.status=disabled ppp.1.password= wpasupplicant.profile.1.network.1.psk=spiffyjuice wpasupplicant.profile.1.network.1.bssid=00:15:6D:B5:F8:05 wpasupplicant.profile.1.network.1.key_mgmt.1.name=WPA-PSK wpasupplicant.profile.1.name=WPA-PSK wpasupplicant.device.1.profile=WPA-PSK aaa.1.wpa.key.1.mgmt=WPA-PSK aaa.1.wpa.psk=spiffyjuice aaa.1.ssid=RadNet1 aaa.1.br.devname=br0 aaa.1.devname=ath0 aaa.1.driver=madwifi aaa.1.wpa.1.pairwise=CCMP aaa.1.wpa=2 aaa.1.status=disabled aaa.status=disabled wpasupplicant.device.1.status=enabled wpasupplicant.status=enabled wireless.1.mac_acl.16.mac= wireless.1.mac_acl.16.status=disabled wireless.1.mac_acl.15.mac= wireless.1.mac_acl.15.status=disabled wireless.1.mac_acl.14.mac= wireless.1.mac_acl.14.status=disabled wireless.1.mac_acl.13.mac= wireless.1.mac_acl.13.status=disabled wireless.1.mac_acl.12.mac= wireless.1.mac_acl.12.status=disabled wireless.1.mac_acl.11.mac= wireless.1.mac_acl.11.status=disabled wireless.1.mac_acl.10.mac= wireless.1.mac_acl.10.status=disabled wireless.1.mac_acl.9.mac= wireless.1.mac_acl.9.status=disabled wireless.1.mac_acl.8.mac= wireless.1.mac_acl.8.status=disabled wireless.1.mac_acl.7.mac= wireless.1.mac_acl.7.status=disabled wireless.1.mac_acl.6.mac= wireless.1.mac_acl.6.status=disabled wireless.1.mac_acl.5.mac= wireless.1.mac_acl.5.status=disabled wireless.1.mac_acl.4.mac= wireless.1.mac_acl.4.status=disabled wireless.1.mac_acl.3.mac= wireless.1.mac_acl.3.status=disabled wireless.1.mac_acl.2.mac= wireless.1.mac_acl.2.status=disabled wireless.1.mac_acl.1.mac= wireless.1.mac_acl.1.status=disabled wireless.1.mac_acl.policy=allow wireless.1.mac_acl.status=disabled wireless.1.ap=00:15:6D:B5:F8:05 wireless.1.authmode=1 radio.1.chanshift=0 radio.1.clksel=0 radio.1.mcastrate=6M radio.1.countrycode=840 wireless.1.macclone=disabled radio.1.channel=36 wireless.1.wds=disabled users.1.status=enabled users.1.name=ubnt users.1.password=VvpvCwhccFv6Q httpd.status=enabled httpd.port=80 radio.status=enabled radio.countrycode=840 radio.ratemodule=ath_rate_sample radio.1.status=enabled radio.1.devname=ath0 radio.1.mode=managed radio.1.rate.max=54M radio.1.rate.auto=enabled radio.1.ieee_mode=ast radio.1.txpower=19 radio.1.acktimeout=22 radio.1.ack.auto=enabled radio.1.rx_antenna_diversity=disabled radio.1.tx_antenna_diversity=disabled radio.1.rx_antenna=2 radio.1.tx_antenna=2 wireless.status=enabled wireless.1.status=enabled wireless.1.devname=ath0 wireless.1.security=none wireless.1.ssid=RadNet2 wireless.1.hide_ssid=disabled bridge.status=enabled bridge.1.devname=br0 bridge.1.fd=1 bridge.1.port.1.devname=eth0 bridge.1.port.2.devname=ath0 netconf.status=enabled netconf.1.status=enabled netconf.1.devname=eth0 netconf.1.ip=0.0.0.0 netconf.1.netmask=255.255.255.0 netconf.1.up=enabled netconf.1.promisc=enabled netconf.2.status=enabled netconf.2.devname=ath0 netconf.2.ip=0.0.0.0 netconf.2.netmask=255.255.255.0 netconf.2.up=enabled netconf.3.status=enabled netconf.3.devname=br0 netconf.3.ip=64.203.123.38 netconf.3.netmask=255.255.255.240 netconf.3.up=enabled dhcpd.status=disabled dhcpd.1.status=disabled dhcpc.status=disabled dhcpc.1.status=disabled dhcpc.1.devname=br0 route.status=enabled route.1.status=enabled route.1.devname=br0 route.1.gateway=64.203.123.33 route.1.ip=0.0.0.0 route.1.netmask=0 ebtables.status=enabled ebtables.1.status=enabled ebtables.1.cmd=-t nat -A PREROUTING --in-interface ath0 -j arpnat --arpnat-target ACCEPT ebtables.2.status=enabled ebtables.2.cmd=-t nat -A POSTROUTING --out-interface ath0 -j arpnat --arpnat-target ACCEPT ebtables.3.status=enabled ebtables.3.cmd=-t broute -A BROUTING --protocol 0x888e --in-interface ath0 -j DROP wireless.1.wmm=disabled wireless.1.wmmlevel=-1 radio.1.rts=off radio.1.frag=off wireless.1.fastframes=enabled wireless.1.frameburst=enabled wireless.1.compression=enabled radio.1.ext_antenna=disabled wireless.1.signal_led1=94 wireless.1.signal_led2=80 wireless.1.signal_led3=73 wireless.1.signal_led4=65 tshaper.status=disabled wireless.1.sper=disabled wireless.1.addmtikie=enabled radio.1.dfs.status= netconf.2.allmulti=disabled wireless.1.l2_isolation=enabled radio.1.thresh62a=28 radio.1.thresh62b=28 radio.1.thresh62g=28 wireless.1.scan_list.status=disabled resolv.nameserver.2.ip=64.192.0.11 ntpclient.status=enabled ntpclient.1.status=enabled ntpclient.1.server=ntp.ucsd.edu wpasupplicant.device.1.devname=ath0 wpasupplicant.device.1.driver=madwifi wpasupplicant.profile.1.network.1.proto.1.name=RSN wpasupplicant.profile.1.network.1.pairwise.1.name=TKIP CCMP wpasupplicant.profile.1.network.1.ssid=RadNet2


RadNet2 (AP)

users.status=enabled wireless.1.security.1.key=1111111111 wireless.1.security.default_key=1 wpasupplicant.profile.1.network.1.psk=spiffyjuice wpasupplicant.profile.1.network.1.bssid= wpasupplicant.profile.1.network.1.key_mgmt.1.name= wpasupplicant.profile.1.name= wpasupplicant.device.1.profile= aaa.1.wpa.key.1.mgmt=WPA-PSK aaa.1.wpa.psk=spiffyjuice aaa.1.ssid=RadNet2 aaa.1.br.devname=br0 aaa.1.devname=ath0 aaa.1.driver=madwifi aaa.1.wpa.1.pairwise=TKIP CCMP aaa.1.wpa=2 ntpclient.1.server=ntp.ucsd.edu ntpclient.1.status=enabled ntpclient.status=enabled resolv.host.1.name=RadNet2 resolv.host.1.status=enabled resolv.nameserver.2.ip=64.192.0.11 ebtables.3.cmd=-t broute -A BROUTING --protocol 0x888e --in-interface ath0 -j DROP ebtables.3.status=enabled ebtables.2.cmd=-t nat -A POSTROUTING --out-interface ath0 -j arpnat --arpnat-target ACCEPT ebtables.2.status=disabled ebtables.1.cmd=-t nat -A PREROUTING --in-interface ath0 -j arpnat --arpnat-target ACCEPT ebtables.1.status=disabled ebtables.status=enabled route.1.netmask=0 route.1.ip=0.0.0.0 route.1.gateway=64.203.123.33 route.1.devname=br0 route.1.status=enabled route.status=enabled dhcpc.1.devname=br0 dhcpc.1.status=disabled dhcpc.status=disabled dhcpd.1.status=disabled dhcpd.status=disabled netconf.3.up=enabled netconf.3.netmask=255.255.255.240 netconf.3.ip=64.203.123.37 netconf.3.devname=br0 netconf.3.status=enabled netconf.2.up=enabled netconf.2.netmask=255.255.255.0 netconf.2.ip=0.0.0.0 netconf.2.devname=ath0 netconf.2.status=enabled netconf.1.promisc=enabled netconf.1.up=enabled netconf.1.netmask=255.255.255.0 netconf.1.ip=0.0.0.0 netconf.1.devname=eth0 netconf.1.status=enabled netconf.status=enabled bridge.1.port.2.devname=ath0 bridge.1.port.1.devname=eth0 bridge.1.fd=1 bridge.1.devname=br0 bridge.status=enabled wireless.1.hide_ssid=disabled wireless.1.ssid=RadNet2 wireless.1.security=none wireless.1.devname=ath0 wireless.1.status=enabled wireless.status=enabled radio.1.tx_antenna=2 radio.1.rx_antenna=2 radio.1.tx_antenna_diversity=disabled radio.1.rx_antenna_diversity=disabled radio.1.ack.auto=enabled radio.1.acktimeout=22 radio.1.txpower=19 radio.1.ieee_mode=ast radio.1.rate.auto=enabled radio.1.rate.max=54M radio.1.mode=master radio.1.devname=ath0 radio.1.status=enabled radio.ratemodule=ath_rate_sample radio.countrycode=840 radio.status=enabled httpd.port=80 httpd.status=enabled users.1.password=VvpvCwhccFv6Q users.1.name=ubnt users.1.status=enabled wireless.1.wds=disabled radio.1.channel=42 wireless.1.macclone=disabled radio.1.countrycode=840 radio.1.mcastrate=6M radio.1.clksel=0 radio.1.chanshift=0 wireless.1.authmode=1 wireless.1.ap= wireless.1.mac_acl.status=disabled wireless.1.mac_acl.policy=allow wireless.1.mac_acl.1.status=disabled wireless.1.mac_acl.1.mac= wireless.1.mac_acl.2.status=disabled wireless.1.mac_acl.2.mac= wireless.1.mac_acl.3.status=disabled wireless.1.mac_acl.3.mac= wireless.1.mac_acl.4.status=disabled wireless.1.mac_acl.4.mac= wireless.1.mac_acl.5.status=disabled wireless.1.mac_acl.5.mac= wireless.1.mac_acl.6.status=disabled wireless.1.mac_acl.6.mac= wireless.1.mac_acl.7.status=disabled wireless.1.mac_acl.7.mac= wireless.1.mac_acl.8.status=disabled wireless.1.mac_acl.8.mac= wireless.1.mac_acl.9.status=disabled wireless.1.mac_acl.9.mac= wireless.1.mac_acl.10.status=disabled wireless.1.mac_acl.10.mac= wireless.1.mac_acl.11.status=disabled wireless.1.mac_acl.11.mac= wireless.1.mac_acl.12.status=disabled wireless.1.mac_acl.12.mac= wireless.1.mac_acl.13.status=disabled wireless.1.mac_acl.13.mac= wireless.1.mac_acl.14.status=disabled wireless.1.mac_acl.14.mac= wireless.1.mac_acl.15.status=disabled wireless.1.mac_acl.15.mac= wireless.1.mac_acl.16.status=disabled wireless.1.mac_acl.16.mac= aaa.status=enabled aaa.1.status=enabled wpasupplicant.status=disabled wpasupplicant.device.1.status=disabled ppp.1.password= ppp.status=disabled iptables.3.status=disabled ppp.1.status=disabled iptables.status=disabled resolv.nameserver.1.ip=64.192.0.10 resolv.nameserver.1.status=enabled resolv.nameserver.2.status=enabled resolv.status=enabled ebtables.50.status=disabled ebtables.51.status=disabled netmode=bridge igmpproxy.status=disabled bridge.1.stp.status=disabled wireless.1.wmm=disabled wireless.1.wmmlevel=-1 radio.1.rts=off radio.1.frag=off wireless.1.fastframes=enabled wireless.1.frameburst=enabled wireless.1.compression=enabled radio.1.ext_antenna=disabled wireless.1.signal_led1=94 wireless.1.signal_led2=80 wireless.1.signal_led3=73 wireless.1.signal_led4=65 tshaper.status=disabled wireless.1.sper=disabled wireless.1.addmtikie=enabled radio.1.dfs.status= netconf.2.allmulti=disabled wireless.1.l2_isolation=disabled radio.1.thresh62a=28 radio.1.thresh62b=28 radio.1.thresh62g=28

[BeAuMaN]

Test Wrap-up post:

Working Security Modes:
WEP
WPA-TKIP
WPA2-TKIP

Non-Working Security Modes:
WPA
WPA-AES
WPA2
WPA2-AES

Theory:
AES encryption is said to be more hardware intensive (as in working at the hardware level), and TKIP is said to be more software intensive (as in working at the soft network level). It's said that when AES was introduced, certain older, cheaper 802.11 units couldn't simply just implement it into a firmware upgrade because of the larger hardware requirements.

Considering the heat in the central valley during the summer, which this week, hovers between 95 and 115 degrees Fahrenheit, it could be possible that the added strain to the hardware from AES is causing the unit to overheat.

However, this theory is a bit far fetched, because the max operating temperature claimed by your datasheets is 158 degrees Fahrenheit, and I'm not really sure if the unit is really getting that hot, even it is in direct sunlight, attached to a metal pole via included zip-ties, and on top of a metal roof. I wasn't much of a physics guy so I really couldn't tell you.

So it's likely my theory is wrong in retrospect, but I thought I'd throw it out there anyway.

As for default WPA and WPA2 not working, I'm going to assume that either way, WPA and WPA2 are -defaulting- to AES instead of TKIP, which would cause it to fail.

Suggestion:
Could you possibly add another feature in the next firmware that, for NanoStations, when you select WPA/WPA2 non-specific encryption, that when it communicates with another unit that's using WPA/WPA2 non-specific encryption, that there's a little box beside it that allows you to choose if it defaults to TKIP or AES.

Will check back on this post later.

Thoughts, everyone?

[BeAuMaN]

As I expected, the overheating theory was a bit far fetched. I tested it in the night on WPA2-AES, and no luck still.

Anything yet on your end, UBNT-Mike? I'll bump sometime during Tuesday if I don't hear anything.

On that note, sometime during next week I won't have a laptop anymore to configure the AP personally via wire, so my ability to test will be hampered and slowed.

Thanks again, UBNT.

[kijoma]

hi,

can confirm 3.1.1 NS5 as a client is happy in WPA2 AES with a MT rb433 AP 3.11

from a previous post of mine tho there is a fight between NS5 as an AP and MT clients with 2.9.x code in anything but WEP and open.

basically in that combo no TKP or AES will work. maybe related?

Bill

[jp498]

I just setup a 5ghz link using rb433 v3.13 for the AP and NS5 for the client radio. I used wpa2-aes with preshared key and its works fine.

Haven't tried MT as a client and NS5 as the AP, as that would be too much work to setup and configure an MT for every customer!

[kijoma]

hi,

be warned, 3.13 has some serious issues with routing, wasted a lot of time here in order to downgrade to 3.11 again.

WPA/WPA2 is fine as MT AP, its only a problem if you use the NS as an AP as we did to fill in coverage for 2 customers and they were MT clients. ok as long as its 3.x and not 2.95.x .

Bill

[UBNT-Mike.Ford]

Hey Guys,

I just set up a MikroTik RB433AH with XR5, and tested all combinations of AES and TKIP between WPA and WPA 2 and had no issues.

Beauman what are you using at the AP?

Thanks,

Mike

[BeAuMaN]

Er... do you mean security?

Same as the station.

If you read my previous posts on testing I did, along with config files, I detailed the method I used.

I currently am running WPA2-TKIP on both the AP and the Station, which works fine.

WPA, WPA-AES, WPA2, WPA2-AES aren't working though.

or did you mean something else?

[UBNT-Mike.Ford]

Hey Beauman,

I have tried using WPA and WPA 2, in both TKIP and AES mode with MikroTik as the AP and NS as the client.

I have also tried NS to NS with V 3.1.1 and V3.2RC2 and both WPA and WPA2 with both TKIP and AES and have not ran into issues getting them connected.

Thanks,

Mike

[BeAuMaN]

Well, as I've posted, I've done this multiple times now (with details). I have my full config files up for you to see. Have you tried the config files I've uploaded in a test situation?

If so, what do I try next? where do I go from here? Thanks.

[jp498]

Here is what I used for the MT and NS5 settings.

http://www.midcoast.com/~jp/ns5aes.png

[kijoma]

looks good to me..


how does the channel shifting work with MT? , not something i have tried. how much does it shift it?

[BeAuMaN]

Well, as I've posted, I've done this multiple times now (with details). I have my full config files up for you to see. Have you tried the config files I've uploaded in a test situation?

If so, what do I try next? where do I go from here? Thanks.


-bump-

Just checking.

[Ceni]

:twisted: :idea: :idea: :idea:

[UBNT-Zy]

Hello BeAuMaN,

>Well, as I've posted, I've done this multiple times now (with details). I have my full config files up for you to see. Have you tried the config files I've uploaded in a test situation?

Yes, I've tried the configuration of your Nanostation with 3 different routeros versions including the latest (3.13). So far I've encountered no issues in any WPA/WPA2 configuration.
Can you please check the routeros log for any clues what's happening? Is there a chance to capture the wireless frames with the sniffer?

Can you please confirm that you are using the latest Nanostation FW (NS5.ar2313.v3.2-rc2.3578.080807.1727.bin)

Thank you,
Z.

[BeAuMaN]

Alright, so as I explained to UBNT-Zy in response, I don't have a computer to use with an 802.11a card, as that was never really my purpose, so I can't sniff wireless packets I think. The laptop I'm currently using for testing has been graciously extended to me until friday.

Anyhoo... installed latest firmware. doesn't fix my problem.

As far as Logs go, I did testing, and the following occurred. Keep in mind that I switched on logging just before turning on WPA2-AES. I have comments (designated by bold) in between log bursts as to what I was doing. Generally I was driving back and forth between both units.

RadNet1


Aug 27 05:47:47 RadNet1 syslog.info syslogd started: BusyBox v1.01 (2008.08.07-14:30+0000)
Aug 27 05:56:08 RadNet1 daemon.info init: ^MReloading /etc/inittab
Aug 27 05:56:08 RadNet1 daemon.info init: ^MProcess '/sbin/ntpclient -s -l -h ntp.ucsd.edu' (pid 468) exited.
Scheduling it for restart.
Aug 27 05:56:09 RadNet1 authpriv.info boa[466]: caught SIGTERM, starting shutdown
Aug 27 05:56:09 RadNet1 daemon.info init: ^MProcess '/bin/wpa_supplicant -D madwifi -i ath0 -c
/etc/wpasupplicant_WPA-PSK.conf' (pid 467) exited. Scheduling it for restart.
Aug 27 05:56:09 RadNet1 daemon.info init: ^MProcess '/bin/boa -d' (pid 466) exited. Scheduling it for restart.
Aug 27 05:56:14 RadNet1 daemon.info init: ^MReloading /etc/inittab
Aug 27 05:56:14 RadNet1 daemon.info init: ^MStarting pid 679, console /dev/null: '/bin/boa'
Aug 27 05:56:14 RadNet1 user.info boa[679]: Boa/0.93.15 started
Aug 27 05:56:14 RadNet1 daemon.info init: ^MStarting pid 680, console /dev/null: '/bin/wpa_supplicant'
Aug 27 05:56:14 RadNet1 daemon.info init: ^MStarting pid 681, console /dev/null: '/sbin/ntpclient'
Aug 27 05:56:14 RadNet1 authpriv.info boa[679]: Authentication successful for ubnt from 64.203.123.40
Aug 27 06:07:47 RadNet1 syslog.info -- MARK --
Aug 27 06:27:47 RadNet1 syslog.info -- MARK --

After reboot of RadNet1, and RadNet 2 previously.

Aug 7 17:32:08 RadNet1 syslog.info syslogd started: BusyBox v1.01 (2008.08.07-14:30+0000)
Aug 7 17:32:08 RadNet1 daemon.info init: ^MStarting pid 269, console /dev/null: '/bin/boa'
Aug 7 17:32:08 RadNet1 daemon.info init: ^MStarting pid 270, console /dev/null: '/bin/wpa_supplicant'
Aug 7 17:32:08 RadNet1 daemon.info init: ^MStarting pid 271, console /dev/null: '/sbin/ntpclient'
Aug 7 17:32:08 RadNet1 daemon.info init: ^MStarting pid 272, console /dev/ttyS0: '/sbin/getty'
Aug 7 17:32:08 RadNet1 user.info boa[269]: Boa/0.93.15 started
Aug 7 17:32:08 RadNet1 authpriv.info boa[269]: Authentication successful for ubnt from 64.203.123.40

After having gotten back from setting RadNet2 to WPA2-TKIP

Aug 7 17:52:08 RadNet1 syslog.info -- MARK --

After having set RadNet1 to WPA2-TKIP (Note: There is now a connection between the two units, in that I can use the remote unit's webUI)

Aug 7 17:57:39 RadNet1 daemon.info init: ^MReloading /etc/inittab
Aug 7 17:57:40 RadNet1 daemon.info init: ^MProcess '/sbin/ntpclient -s -l -h ntp.ucsd.edu' (pid 271) exited.
Scheduling it for restart.
Aug 7 17:57:40 RadNet1 authpriv.info boa[269]: caught SIGTERM, starting shutdown
Aug 7 17:57:41 RadNet1 daemon.info init: ^MProcess '/bin/wpa_supplicant -D madwifi -i ath0 -c
/etc/wpasupplicant_WPA-PSK.conf' (pid 270) exited. Scheduling it for restart.
Aug 7 17:57:41 RadNet1 daemon.info init: ^MProcess '/bin/boa -d' (pid 269) exited. Scheduling it for restart.
Aug 7 17:57:45 RadNet1 daemon.info init: ^MReloading /etc/inittab
Aug 7 17:57:45 RadNet1 daemon.info init: ^MStarting pid 482, console /dev/null: '/bin/boa'
Aug 7 17:57:45 RadNet1 user.info boa[482]: Boa/0.93.15 started
Aug 7 17:57:45 RadNet1 daemon.info init: ^MStarting pid 483, console /dev/null: '/bin/wpa_supplicant'
Aug 7 17:57:45 RadNet1 authpriv.info boa[482]: Authentication successful for ubnt from 64.203.123.40
Aug 7 17:57:45 RadNet1 daemon.info init: ^MStarting pid 484, console /dev/null: '/sbin/ntpclient'

After having gotten back, and reconnected the Internet line to RadNet2, and having gone to google real quick:

Aug 27 07:13:22 RadNet1 syslog.info -- MARK --


RadNet2

Aug 27 05:47:27 RadNet2 syslog.info syslogd started: BusyBox v1.01 (2008.08.07-14:30+0000)
Aug 27 05:47:34 RadNet2 daemon.info hostapd: ath0: STA 00:15:6d:b5:f7:a0 IEEE 802.11: associated
Aug 27 05:47:34 RadNet2 daemon.info hostapd: ath0: STA 00:15:6d:b5:f7:a0 WPA: pairwise key handshake completed (RSN)
Aug 27 05:47:35 RadNet2 authpriv.info boa[495]: Authentication successful for ubnt from 64.203.123.40
Aug 27 05:47:41 RadNet2 daemon.info hostapd: ath0: STA 00:15:6d:b5:f7:a0 IEEE 802.11: disassociated
Aug 27 05:47:41 RadNet2 daemon.info hostapd: ath0: STA 00:15:6d:b5:f7:a0 IEEE 802.11: associated
Aug 27 05:47:41 RadNet2 daemon.info hostapd: ath0: STA 00:15:6d:b5:f7:a0 IEEE 802.11: disassociated
Aug 27 05:47:50 RadNet2 daemon.info hostapd: ath0: STA 00:15:6d:b5:f7:a0 IEEE 802.11: associated
Aug 27 05:47:50 RadNet2 daemon.info hostapd: ath0: STA 00:15:6d:b5:f7:a0 WPA: pairwise key handshake completed (RSN)
Aug 27 05:55:08 RadNet2 daemon.info init: ^MReloading /etc/inittab
Aug 27 05:55:08 RadNet2 daemon.info init: ^MProcess '/sbin/ntpclient -s -l -h ntp.ucsd.edu' (pid 497) exited. Scheduling it for restart.
Aug 27 05:55:08 RadNet2 authpriv.info boa[495]: caught SIGTERM, starting shutdown
Aug 27 05:55:09 RadNet2 daemon.info init: ^MProcess '/bin/hostapd /etc/aaa.cfg' (pid 496) exited. Scheduling it for restart.
Aug 27 05:55:09 RadNet2 daemon.info init: ^MProcess '/bin/boa -d' (pid 495) exited. Scheduling it for restart.
Aug 27 05:55:14 RadNet2 daemon.info init: ^MReloading /etc/inittab
Aug 27 05:55:14 RadNet2 daemon.info init: ^MStarting pid 705, console /dev/null: '/bin/boa'
Aug 27 05:55:14 RadNet2 user.info boa[705]: Boa/0.93.15 started
Aug 27 05:55:14 RadNet2 daemon.info init: ^MStarting pid 706, console /dev/null: '/bin/hostapd'
Aug 27 05:55:14 RadNet2 daemon.info init: ^MStarting pid 707, console /dev/null: '/sbin/ntpclient'
Aug 27 05:56:17 RadNet2 daemon.info hostapd: ath0: STA 00:15:6d:b5:f7:a0 IEEE 802.11: associated
Aug 27 05:56:17 RadNet2 daemon.info hostapd: ath0: STA 00:15:6d:b5:f7:a0 WPA: pairwise key handshake completed (RSN)
Aug 27 06:05:19 RadNet2 daemon.info hostapd: ath0: STA 00:15:6d:b5:f7:a0 IEEE 802.11: deauthenticated due to local deauth request
Aug 27 06:05:19 RadNet2 daemon.info hostapd: ath0: STA 00:15:6d:b5:f7:a0 IEEE 802.11: disassociated
Aug 27 06:05:20 RadNet2 daemon.info hostapd: ath0: STA 00:15:6d:b5:f7:a0 IEEE 802.11: associated
Aug 27 06:05:20 RadNet2 daemon.info hostapd: ath0: STA 00:15:6d:b5:f7:a0 WPA: pairwise key handshake completed (RSN)
Aug 27 06:07:27 RadNet2 syslog.info -- MARK --
Aug 27 06:15:19 RadNet2 daemon.info hostapd: ath0: STA 00:15:6d:b5:f7:a0 IEEE 802.11: deauthenticated due to local deauth request
Aug 27 06:15:19 RadNet2 daemon.info hostapd: ath0: STA 00:15:6d:b5:f7:a0 IEEE 802.11: disassociated
Aug 27 06:15:20 RadNet2 daemon.info hostapd: ath0: STA 00:15:6d:b5:f7:a0 IEEE 802.11: associated
Aug 27 06:15:20 RadNet2 daemon.info hostapd: ath0: STA 00:15:6d:b5:f7:a0 WPA: pairwise key handshake completed (RSN)
Aug 27 06:19:28 RadNet2 authpriv.info boa[705]: Authentication successful for ubnt from 64.203.123.41

After Rebooting AP, but not Station

Aug 7 17:32:08 RadNet2 syslog.info syslogd started: BusyBox v1.01 (2008.08.07-14:30+0000)
Aug 7 17:32:08 RadNet2 daemon.info init: ^MStarting pid 267, console /dev/null: '/bin/boa'
Aug 7 17:32:08 RadNet2 daemon.info init: ^MStarting pid 268, console /dev/null: '/bin/hostapd'
Aug 7 17:32:08 RadNet2 daemon.info init: ^MStarting pid 269, console /dev/null: '/sbin/ntpclient'
Aug 7 17:32:08 RadNet2 daemon.info init: ^MStarting pid 270, console /dev/ttyS0: '/sbin/getty'
Aug 7 17:32:08 RadNet2 user.info boa[267]: Boa/0.93.15 started
Aug 7 17:32:08 RadNet2 authpriv.info boa[267]: Authentication successful for ubnt from 64.203.123.41
Aug 7 17:32:13 RadNet2 daemon.info hostapd: ath0: STA 00:15:6d:b5:f7:a0 IEEE 802.11: associated
Aug 7 17:32:13 RadNet2 daemon.info hostapd: ath0: STA 00:15:6d:b5:f7:a0 WPA: pairwise key handshake completed (RSN)
Aug 7 17:35:25 RadNet2 daemon.info hostapd: ath0: STA 00:15:6d:b5:f7:a0 IEEE 802.11: disassociated
Aug 7 17:35:29 RadNet2 daemon.info hostapd: ath0: STA 00:15:6d:b5:f7:a0 IEEE 802.11: associated
Aug 7 17:35:30 RadNet2 daemon.info hostapd: ath0: STA 00:15:6d:b5:f7:a0 WPA: pairwise key handshake completed (RSN)

After having drove back over here to RadNet2

Aug 7 17:42:13 RadNet2 daemon.info hostapd: ath0: STA 00:15:6d:b5:f7:a0 IEEE 802.11: deauthenticated due to local deauth request
Aug 7 17:42:13 RadNet2 daemon.info hostapd: ath0: STA 00:15:6d:b5:f7:a0 IEEE 802.11: disassociated
Aug 7 17:42:14 RadNet2 daemon.info hostapd: ath0: STA 00:15:6d:b5:f7:a0 IEEE 802.11: associated
Aug 7 17:42:14 RadNet2 daemon.info hostapd: ath0: STA 00:15:6d:b5:f7:a0 WPA: pairwise key handshake completed (RSN)
Aug 7 17:43:34 RadNet2 daemon.info hostapd: ath0: STA 00:15:6d:b5:f7:a0 IEEE 802.11: disassociated
Aug 7 17:44:03 RadNet2 daemon.info hostapd: ath0: STA 00:15:6d:b5:f7:a0 IEEE 802.11: associated
Aug 7 17:44:03 RadNet2 daemon.info hostapd: ath0: STA 00:15:6d:b5:f7:a0 WPA: pairwise key handshake completed (RSN)
Aug 7 17:52:08 RadNet2 syslog.info -- MARK --
Aug 7 17:52:13 RadNet2 daemon.info hostapd: ath0: STA 00:15:6d:b5:f7:a0 IEEE 802.11: deauthenticated due to local deauth request
Aug 7 17:52:13 RadNet2 daemon.info hostapd: ath0: STA 00:15:6d:b5:f7:a0 IEEE 802.11: disassociated
Aug 7 17:52:14 RadNet2 daemon.info hostapd: ath0: STA 00:15:6d:b5:f7:a0 IEEE 802.11: associated
Aug 7 17:52:14 RadNet2 daemon.info hostapd: ath0: STA 00:15:6d:b5:f7:a0 WPA: pairwise key handshake completed (RSN)

after having set RadNet2 to WPA2-TKIP (RadNet1 Not setup yet)

Aug 7 17:56:34 RadNet2 daemon.info init: ^MReloading /etc/inittab
Aug 7 17:56:34 RadNet2 daemon.info init: ^MProcess '/sbin/ntpclient -s -l -h ntp.ucsd.edu' (pid 269) exited. Scheduling it for restart.
Aug 7 17:56:34 RadNet2 authpriv.info boa[267]: caught SIGTERM, starting shutdown
Aug 7 17:56:35 RadNet2 daemon.info init: ^MProcess '/bin/hostapd /etc/aaa.cfg' (pid 268) exited. Scheduling it for restart.
Aug 7 17:56:35 RadNet2 daemon.info init: ^MProcess '/bin/boa -d' (pid 267) exited. Scheduling it for restart.
Aug 7 17:56:40 RadNet2 daemon.info init: ^MReloading /etc/inittab
Aug 7 17:56:40 RadNet2 daemon.info init: ^MStarting pid 493, console /dev/null: '/bin/boa'
Aug 7 17:56:40 RadNet2 user.info boa[493]: Boa/0.93.15 started
Aug 7 17:56:40 RadNet2 daemon.info init: ^MStarting pid 494, console /dev/null: '/bin/hostapd'
Aug 7 17:56:40 RadNet2 authpriv.info boa[493]: Authentication successful for ubnt from 64.203.123.41
Aug 7 17:56:40 RadNet2 daemon.info init: ^MStarting pid 495, console /dev/null: '/sbin/ntpclient'

Had a quick second-thought to test WPA2-standard at AP end to see if it picks up station (It doesn't)

Aug 7 17:59:26 RadNet2 daemon.info init: ^MReloading /etc/inittab
Aug 7 17:59:27 RadNet2 daemon.info init: ^MProcess '/sbin/ntpclient -s -l -h ntp.ucsd.edu' (pid 495) exited. Scheduling it for restart.
Aug 7 17:59:27 RadNet2 authpriv.info boa[493]: caught SIGTERM, starting shutdown
Aug 7 17:59:28 RadNet2 daemon.info init: ^MProcess '/bin/hostapd /etc/aaa.cfg' (pid 494) exited. Scheduling it for restart.
Aug 7 17:59:28 RadNet2 daemon.info init: ^MProcess '/bin/boa -d' (pid 493) exited. Scheduling it for restart.
Aug 7 17:59:33 RadNet2 daemon.info init: ^MReloading /etc/inittab
Aug 7 17:59:33 RadNet2 daemon.info init: ^MStarting pid 693, console /dev/null: '/bin/boa'
Aug 7 17:59:33 RadNet2 user.info boa[693]: Boa/0.93.15 started
Aug 7 17:59:33 RadNet2 daemon.info init: ^MStarting pid 694, console /dev/null: '/bin/hostapd'
Aug 7 17:59:33 RadNet2 daemon.info init: ^MStarting pid 695, console /dev/null: '/sbin/ntpclient'
Aug 7 17:59:33 RadNet2 authpriv.info boa[693]: Authentication successful for ubnt from 64.203.123.41
Aug 7 17:59:40 RadNet2 daemon.info hostapd: ath0: STA 00:15:6d:b5:f7:a0 IEEE 802.11: associated
Aug 7 17:59:41 RadNet2 daemon.info hostapd: ath0: STA 00:15:6d:b5:f7:a0 WPA: pairwise key handshake completed (RSN)

Switched back again to WPA2-TKIP, drove over to RadNet1 afterward.

Aug 7 18:02:13 RadNet2 daemon.info init: ^MReloading /etc/inittab
Aug 7 18:02:13 RadNet2 daemon.info init: ^MProcess '/sbin/ntpclient -s -l -h ntp.ucsd.edu' (pid 695) exited. Scheduling it for restart.
Aug 7 18:02:14 RadNet2 authpriv.info boa[693]: caught SIGTERM, starting shutdown
Aug 7 18:02:14 RadNet2 daemon.info init: ^MProcess '/bin/hostapd /etc/aaa.cfg' (pid 694) exited. Scheduling it for restart.
Aug 7 18:02:14 RadNet2 daemon.info init: ^MProcess '/bin/boa -d' (pid 693) exited. Scheduling it for restart.
Aug 7 18:02:19 RadNet2 daemon.info init: ^MReloading /etc/inittab
Aug 7 18:02:19 RadNet2 daemon.info init: ^MStarting pid 888, console /dev/null: '/bin/boa'
Aug 7 18:02:19 RadNet2 user.info boa[888]: Boa/0.93.15 started
Aug 7 18:02:19 RadNet2 daemon.info init: ^MStarting pid 889, console /dev/null: '/bin/hostapd'
Aug 7 18:02:19 RadNet2 authpriv.info boa[888]: Authentication successful for ubnt from 64.203.123.41
Aug 7 18:02:19 RadNet2 daemon.info init: ^MStarting pid 890, console /dev/null: '/sbin/ntpclient'

after having drove back to disconnect laptop

Aug 7 18:09:41 RadNet2 daemon.info hostapd: ath0: STA 00:15:6d:b5:f7:a0 IEEE 802.11: associated
Aug 7 18:09:41 RadNet2 daemon.info hostapd: ath0: STA 00:15:6d:b5:f7:a0 WPA: pairwise key handshake completed (RSN)
Aug 7 18:09:52 RadNet2 authpriv.info boa[888]: Authentication successful for ubnt from 64.203.123.40
Aug 7 18:12:08 RadNet2 syslog.info -- MARK --
Aug 7 18:12:22 RadNet2 daemon.info hostapd: ath0: STA 00:15:6d:b5:f7:a0 WPA: group key handshake completed (RSN)
Aug 7 18:17:22 RadNet2 authpriv.info boa[888]: Authentication successful for ubnt from 64.203.123.41

After having gotten back, and reconnected the Internet line to RadNet2, and having gone to google real quick (Accessed Remotely):

Aug 27 07:08:24 RadNet2 daemon.info hostapd: ath0: STA 00:15:6d:b5:f7:a0 WPA: group key handshake completed (RSN)
Aug 27 07:18:24 RadNet2 daemon.info hostapd: ath0: STA 00:15:6d:b5:f7:a0 WPA: group key handshake completed (RSN)
Aug 27 07:21:29 RadNet2 syslog.info -- MARK --
Aug 27 07:21:47 RadNet2 authpriv.info boa[888]: Authentication successful for ubnt from 64.203.123.40


Keep in mind my personal notes are made after -viewing- the log.

The times and dates are off, doin't know why, but this is over the same period of time on the same night.

Hope this helps... somehow.

[UBNT-Zy]

Hello BeAuMaN,
there is only clue in the nanostation logs that "WPA: group key handshake" is not initiated after "Pairwise key handshake completed" thus the client is not authenticated. Can you please check if using "tkip" group cipher in routeros side solves an issue while "aes" unicast cipher is selected?

Can you please check what is said in routeros system log?

Thank you,
Z.

[BeAuMaN]

Er... apologies, Zy... but sadly I'm not sure what you're asking me to do. If you, or someone else could translate, that'd be great. Apologies for my ignorance.

Oh, I realized (now that it's not late at night) that I should include a bit more info for each unit just for reference in the logs.

(NS5) RadNet2:
Bridge/AP
00:15:6D:B5:F8:05
64.203.123.37


(NS5) RadNet1
Bridge/Station
00:15:6D:B5:F7:A0
64.203.123.38

(WRT54G) RadNet0
Gateway
00:13:10:73:8E:3F (At least on WAN Port)
64.203.123.40
Connected via Ethernet cable to RadNet1


As for 64.203.123.41, that is just the laptop I'm using of my friend's, that I connect to RadNet2 in place of the ISP's ethernet so I can access the WebUI of RadNet2 if the connection between RadNet1 and RadNet2 are down.

Anyhoo, I can probably test again tonight for whatever it is you want me to try.

[UBNT-Zy]

Hello BeAuMaN,
sorry, my fault, just was confused with the jp498's setup in this post where routeros screenshot is attached. I'm continuing the further investigation of your configuration. Will be back with more information when I'l have it. Thank you.

Z.

[BeAuMaN]

Thanks Zy. I look forward to your findings. I'll bump this post on Tuesday if I don't hear anything.

Thanks again!

[UBNT-Zy]

Hello BeAuMaN,

I'm not sure it that was the case of yours but I was able to recreate strange behavior with WPA2 - station had refused to authenticate after dozen of tries to switch from TKIP to AES, however it can be somewhat related to the so called "blacklisting" as the station can become blacklisted if it supplies wrong wpa encryption keys for number of times. After short time / hw reboot the issue had gone. Will continue on investigation on this. At the meantime, can you please re-check is the full HW reboot of the both link endpoints does not solves the issue?

Thank you,
Z.

[BeAuMaN]

Ah, it's good to find out I was not completely crazy. I'll definitely try this, just in case I only HW-reset one side.... sadly, I've lost access to my friend's laptop... so I'll run this test likely on a night when I can lug my big 18"x18"x18" computer over to the workshop :P

Really appreciate it Zy, thanks!

Real quick though... by Full HW Reboot, you mean the reboot feature under the "System" tab of AirOS? A powerdown of the unit? or...?

[UBNT-Zy]

Hello BeAuMaN,

>by Full HW Reboot, you mean...

Sorry for ambiguity, actually I mean the cold reboot or let's say power off/power on cycle.

Thanks,
Z.

[Ron]

Yes, I've tried the configuration of your Nanostation with 3 different routeros versions including the latest (3.13). So far I've encountered no issues in any WPA/WPA2 configuration.

Try taking two PS5s, with the latest firmware, and set them in AP WDS and Station WDS mode. Then enable WPA2-AES and see if they associate AND pass traffic.

All I see is this:

Sep 9 16:48:59 PaNETma5-A1 daemon.info hostapd: ath0: STA 00:15:6d:b5:16:21 IEEE 802.11: deauthenticated due to local deauth request
Sep 9 16:48:59 PaNETma5-A1 daemon.info hostapd: ath0: STA 00:15:6d:b5:16:21 IEEE 802.11: disassociated
Sep 9 16:49:00 PaNETma5-A1 daemon.info hostapd: ath0: STA 00:15:6d:b5:16:21 IEEE 802.11: associated
Sep 9 16:49:03 PaNETma5-A1 daemon.info hostapd: ath0: STA 00:15:6d:b5:16:21 IEEE 802.11: associated
Sep 9 16:49:03 PaNETma5-A1 daemon.info hostapd: ath0: STA 00:15:6d:b5:16:21 IEEE 802.11: associated
Sep 9 16:49:04 PaNETma5-A1 daemon.info hostapd: ath0: STA 00:15:6d:b5:16:21 IEEE 802.11: deauthenticated due to local deauth request
Sep 9 16:49:04 PaNETma5-A1 daemon.info hostapd: ath0: STA 00:15:6d:b5:16:21 IEEE 802.11: disassociated
Sep 9 16:49:06 PaNETma5-A1 daemon.info hostapd: ath0: STA 00:15:6d:b5:16:21 IEEE 802.11: associated
Sep 9 16:49:09 PaNETma5-A1 daemon.info hostapd: ath0: STA 00:15:6d:b5:16:21 IEEE 802.11: associated
Sep 9 16:49:10 PaNETma5-A1 daemon.info hostapd: ath0: STA 00:15:6d:b5:16:21 IEEE 802.11: deauthenticated due to local deauth request
Sep 9 16:49:10 PaNETma5-A1 daemon.info hostapd: ath0: STA 00:15:6d:b5:16:21 IEEE 802.11: disassociated

[carvalhaes]

Hi Guys!

This AirOS bug was fixed???