problem with routerstation

[marek001]

sry i don't no where to posto this so i gonna try here..

i can't connect to the routerstation trough telnet or ssh...

when i try telnet 192.168.1.20 (start>run) telnet window apper and i say connecting to 192.168.1.20 and it wont connect...

my ip adress is 192.168.1.84 and when i try to ping 192.168.1.20 it work but when i try telnet 192.168.1.20 the ping is stop going...i must then change my ip to like 192.168.1.2 and then the ping going again...

can someone help me??

the rs i brand new and like 2 h old..

tnx
bye

[riskable]

sry i don't no where to posto this so i gonna try here..

i can't connect to the routerstation trough telnet or ssh...

when i try telnet 192.168.1.20 (start>run) telnet window apper and i say connecting to 192.168.1.20 and it wont connect...

my ip adress is 192.168.1.84 and when i try to ping 192.168.1.20 it work but when i try telnet 192.168.1.20 the ping is stop going...i must then change my ip to like 192.168.1.2 and then the ping going again...

can someone help me??

the rs i brand new and like 2 h old..

tnx
bye

This belongs in the RouterStation forum (http://www.ubnt.com/forum/forumdisplay.php?f=23) (which is under the Ubiquiti Embedded System and Mini-PCI based Products (http://www.ubnt.com/forum/forumdisplay.php?f=33) category). Having said that, it sounds like your netmask is set incorrectly on your RouterStation...

If you can ping 192.168.1.20 (the RS device) from 192.168.1.2 but not 192.168.1.84 it is likely that your netmask is something other than 255.255.255.0 (probably 255.255.255.128 or something similar). Did you change it?

Also, have you tried using SSH to get into the device? I think telnet is disabled on the pre-installed image (telnet is *bad*). For reference, the default user/password is root/ubnt... So just set your PC's IP to 192.168.1.2 (the one you know works from your ping results) and then SSH in: "ssh root@192.168.1.20" and use password, "ubnt".

For reference, the RouterStation setup guide is here (http://wiki.ubnt.com/wiki/index.php/RouterStation_OpenWRT_SW_Setup_Guide).

[marek001]

there is the problem...

i can ping it from hole 192.168.1.0/24 subnet but when i try to connect trough telnet the rs goes off or somthing i dont not...becouse when i run telnet then i cant ping it any more...

what program do i must juse so that i can connect to rs trought ssh??

i have try'd http://192.168.1.20 and it say's error 404

[riskable]

there is the problem...

i can ping it from hole 192.168.1.0/24 subnet but when i try to connect trough telnet the rs goes off or somthing i dont not...becouse when i run telnet then i cant ping it any more...

what program do i must juse so that i can connect to rs trought ssh??

i have try'd http://192.168.1.20 and it say's error 404

To connect to your RouterStation through SSH you need an SSH program. If you're in Windows that's likely going to be Putty (http://www.chiark.greenend.org.uk/~sgtatham/putty/download.html). If you're using Linux just type "ssh root@192.168.1.20" into a terminal and enter your password at the prompt.

HOWEVER, I should mention that I had a similar problem with my RouterStation once after I flashed it with a custom firmware. After pulling my hair out for a while I just reflashed it (with the same firmware) and everything started working properly. So it could just be a bad flash (wouldn't be the first time I've experienced such a problem with embedded systems).

Also, I've seen similar problems to this with bad power supplies or bad/too long ethernet cables (when using PoE). The first power supply I used with my RouterStation was a cheap Chinese-made hunk of junk and I had all sorts of strange application crashes until I switched to a Ubiquiti POE-15.

[marek001]

tnx alot...i have now fixed the problem...
i have reflashed it again and now i can connect do ssh...but now im logd in like root login but it say that permission is denied...

and how can i now put some web interface on it...p.s. im not connected to the internet trought rs

tnx
bye

[FCC-PT]

Let me tell you I had the same trouble when I first received my RS-Pro...
Simply couldn't login, telnet, SSH (putty), linux terminal nothing worked till I flashed with trunk image.

Strange no?